At the last PHDays 9, we held a competition to hack a gas pumping plant - competition . There were three booths on the site with different security settings (No Security, Low Security, High Security), emulating the same industrial process: air was pumped into (and then descended) under pressure.
Despite the different security parameters, the test bench hardware was the same: PLC Siemens Simatic S7-300 series; emergency blow button and pressure measuring device (connected to PLC digital inputs (DI)); inflation and deflation valves (connected to PLC digital outputs (DO)) - see figure below.
The PLC, depending on the pressure readings and in accordance with its program, made a decision to deflate or inflate the balloon (opened and closed the corresponding valves). However, a manual control mode was provided on all stands, which made it possible to control the states of the valves without any restrictions.
The stands differed in the complexity of turning on this mode: it was the easiest to do it on an unprotected stand, and, accordingly, more difficult on the High Security stand.
Five of the six tasks were completed in two days; the participant who won first place earned 233 points (he spent a week preparing for the competition). Three winners: I place — a1exdandy, II — Rubikoid, III — Ze.
However, during PHDays, none of the participants could overcome all three stands, so we decided to make an online competition and published the most difficult task in early June. Participants had to complete the task in a month, find the flag, describe the solution in detail and in an interesting way.
Under the cut, we publish an analysis of the best solution to the task sent over the month, it was found by Alexey Kovrizhnykh (a1exdandy) from Digital Security, who took first place in the competition during PHDays. Below we present its text with our comments.
Initial analysis
So, in the task there was an archive with files:
- block_upload_traffic.pcapng
- DB100.bin
- hints.txt
The hints.txt file contains the necessary information and hints for solving the task. Here is its content:
- Petrovich told me yesterday that you can load blocks into Step7 from PlcSim.
- The stand used PLC Siemens Simatic series S7-300.
- PlcSim is a PLC emulator that allows you to run and debug programs for Siemens S7 PLCs.
The DB100.bin file appears to contain a DB100 PLC data block: 00000000: 0100 0102 6e02 0401 0206 0100 0101 0102 ....n........... 00000010: 1002 0501 0202 2002 0501 0206 ..w............. 0100: 0102 00000020 0102 7702 0401 0206 0100a0103 0102 u............... 0: 02 00000030 0501 0202 1602 0501 0206 0100 ..........&..... 0104: 0102c00000040 7502 0401 0206 0100 0105 0102 0 L...........02... 0501: 00000050 0202 1602 0501 0206 0100a0106 0102 3402 4 ................ 00000060: 0401 0206 0100 0107a 0102 2602 0501 0202 .........00000070..... 4a02: 0501 0206b 0100 0108 0102 3302 0401 3 00000080 ......".....F... 0206b0100: 0109 0102 0c 02 0501 0202 1602 00000090 ........0501....... 0206c0100: 010d 0102 3702a0401 0206 7 000000 0 0100 010 ................ 0102d2202: 0501 0202e 4602 0501d000000 0 0206 0100 010f ......m......... 0102e3302: 0401 0206 0100 3 000000 0 010 0102 ........#...... .0f02:0501 ....0202........... 1602 0501 0206 000000 0 0100 010 0102 ..6...........&.02: 0401 0206 0100c010 000000 0 0102 ....L.......
As the name suggests, the block_upload_traffic.pcapng file contains a dump of block upload traffic on the PLC.
It is worth noting that this traffic dump on the competition site during the conference was a little more difficult to obtain. To do this, it was necessary to understand the script from the project file for TeslaSCADA2. From it it was possible to understand where the dump encrypted with RC4 is located and what key should be used to decrypt it. On-site data block dumps could be obtained using the S7 protocol client. I used the demo client from the Snap7 package for this.
Extract signal processing blocks from a traffic dump
Looking at the contents of the dump, you can understand that signal processing blocks OB1, FC1, FC2 and FC3 are transferred in it:
These blocks need to be removed. This can be done, for example, with the following script, after converting traffic from the pcapng format to pcap:
#!/usr/bin/env python2
import struct
from scapy.all import *
packets = rdpcap('block_upload_traffic.pcap')
s7_hdr_struct = '>BBHHHHBB'
s7_hdr_sz = struct.calcsize(s7_hdr_struct)
tpkt_cotp_sz = 7
names = iter(['OB1.bin', 'FC1.bin', 'FC2.bin', 'FC3.bin'])
buf = ''
for packet in packets:
if packet.getlayer(IP).src == '10.0.102.11':
tpkt_cotp_s7 = str(packet.getlayer(TCP).payload)
if len(tpkt_cotp_s7) < tpkt_cotp_sz + s7_hdr_sz:
continue
s7 = tpkt_cotp_s7[tpkt_cotp_sz:]
s7_hdr = s7[:s7_hdr_sz]
param_sz = struct.unpack(s7_hdr_struct, s7_hdr)[4]
s7_param = s7[12:12+param_sz]
s7_data = s7[12+param_sz:]
if s7_param in ('x1ex00', 'x1ex01'): # upload
buf += s7_data[4:]
elif s7_param == 'x1f':
with open(next(names), 'wb') as f:
f.write(buf)
buf = ''Examining the received blocks, you can see that they always start with bytes 70 70 (pp). Now you need to learn how to analyze them. The task hint suggests that PlcSim must be used for this.
Getting human-readable instructions from blocks
First, let's try to program the S7-PlcSim by loading several blocks with repeated instructions (= Q 0.0) into it using the Simatic Manager software, and save the PLC received in the emulator to the example.plc file. By looking at the contents of the file, you can easily determine the beginning of the downloaded blocks by the signature 70 70 that we discovered earlier. Before the blocks, apparently, the block size is written as a 4-byte little-endian value.
After we got the information about the structure of plc files, the following plan of action for reading PLC S7 programs appeared:
- Using Simatic Manager, we create a block structure in S7-PlcSim similar to the one we got from the dump. The block sizes must match (achieved by filling the blocks with the required number of instructions) and their identifiers (OB1, FC1, FC2, FC3).
- Save the PLC to a file.
- We replace the contents of the blocks in the resulting file with blocks from the traffic dump. The beginning of the blocks is determined by the signature.
- The resulting file is loaded into S7-PlcSim and we look at the contents of the blocks in the Simatic Manager.
Blocks can be replaced, for example, with the following code:
with open('original.plc', 'rb') as f:
plc = f.read()
blocks = []
for fname in ['OB1.bin', 'FC1.bin', 'FC2.bin', 'FC3.bin']:
with open(fname, 'rb') as f:
blocks.append(f.read())
i = plc.find(b'pp')
for block in blocks:
plc = plc[:i] + block + plc[i+len(block):]
i = plc.find(b'pp', i + 1)
with open('target.plc', 'wb') as f:
f.write(plc)Aleksey took a perhaps more difficult, but still the right path. We assumed that participants would use the NetToPlcSim program to communicate with PlcSim over the network, upload blocks to PlcSim via Snap7, and then download these blocks as a project from PlcSim using the development environment.
By opening the resulting file in S7-PlcSim, you can read the overwritten blocks using Simatic Manager. The main functions of device management are recorded in block FC1. Particularly noteworthy is the #TEMP0 variable, which, when turned on, seems to put the PLC control into manual mode based on the M2.2 and M2.3 bit memory values. The #TEMP0 value is set by the FC3 function.
To solve the task, it is necessary to analyze the FC3 function and understand what needs to be done so that it returns a logical unit.
The PLC signal processing blocks at the Low Security booth at the competition site were arranged in a similar way, but to set the value of the #TEMP0 variable, it was enough to write the string my ninja way to the DB1 block. Checking the value in the block was clear and did not require deep knowledge of the block programming language. Obviously, at the High Security level, it will be much more difficult to achieve manual control and it will be necessary to understand the intricacies of the STL language (one of the ways to program the S7 PLC).
Reverse block FC3
The content of the FC3 block in the STL representation:
L B#16#0
T #TEMP13
T #TEMP15
L P#DBX 0.0
T #TEMP4
CLR
= #TEMP14
M015: L #TEMP4
LAR1
OPN DB 100
L DBLG
TAR1
<=D
JC M016
L DW#16#0
T #TEMP0
L #TEMP6
L W#16#0
<>I
JC M00d
L P#DBX 0.0
LAR1
M00d: L B [AR1,P#0.0]
T #TEMP5
L W#16#1
==I
JC M007
L #TEMP5
L W#16#2
==I
JC M008
L #TEMP5
L W#16#3
==I
JC M00f
L #TEMP5
L W#16#4
==I
JC M00e
L #TEMP5
L W#16#5
==I
JC M011
L #TEMP5
L W#16#6
==I
JC M012
JU M010
M007: +AR1 P#1.0
L P#DBX 0.0
LAR2
L B [AR1,P#0.0]
L C#8
*I
+AR2
+AR1 P#1.0
L B [AR1,P#0.0]
JL M003
JU M001
JU M002
JU M004
M003: JU M005
M001: OPN DB 101
L B [AR2,P#0.0]
T #TEMP0
JU M006
M002: OPN DB 101
L B [AR2,P#0.0]
T #TEMP1
JU M006
M004: OPN DB 101
L B [AR2,P#0.0]
T #TEMP2
JU M006
M00f: +AR1 P#1.0
L B [AR1,P#0.0]
L C#8
*I
T #TEMP11
+AR1 P#1.0
L B [AR1,P#0.0]
T #TEMP7
L P#M 100.0
LAR2
L #TEMP7
L C#8
*I
+AR2
TAR2 #TEMP9
TAR1 #TEMP4
OPN DB 101
L P#DBX 0.0
LAR1
L #TEMP11
+AR1
LAR2 #TEMP9
L B [AR2,P#0.0]
T B [AR1,P#0.0]
L #TEMP4
LAR1
JU M006
M008: +AR1 P#1.0
L B [AR1,P#0.0]
T #TEMP3
+AR1 P#1.0
L B [AR1,P#0.0]
JL M009
JU M00b
JU M00a
JU M00c
M009: JU M005
M00b: L #TEMP3
T #TEMP0
JU M006
M00a: L #TEMP3
T #TEMP1
JU M006
M00c: L #TEMP3
T #TEMP2
JU M006
M00e: +AR1 P#1.0
L B [AR1,P#0.0]
T #TEMP7
L P#M 100.0
LAR2
L #TEMP7
L C#8
*I
+AR2
TAR2 #TEMP9
+AR1 P#1.0
L B [AR1,P#0.0]
T #TEMP8
L P#M 100.0
LAR2
L #TEMP8
L C#8
*I
+AR2
TAR2 #TEMP10
TAR1 #TEMP4
LAR1 #TEMP9
LAR2 #TEMP10
L B [AR1,P#0.0]
L B [AR2,P#0.0]
AW
INVI
T #TEMP12
L B [AR1,P#0.0]
L B [AR2,P#0.0]
OW
L #TEMP12
AW
T B [AR1,P#0.0]
L DW#16#0
T #TEMP0
L MB 101
T #TEMP1
L MB 102
T #TEMP2
L #TEMP4
LAR1
JU M006
M011: +AR1 P#1.0
L B [AR1,P#0.0]
T #TEMP7
L P#M 100.0
LAR2
L #TEMP7
L C#8
*I
+AR2
TAR2 #TEMP9
+AR1 P#1.0
L B [AR1,P#0.0]
T #TEMP8
L P#M 100.0
LAR2
L #TEMP8
L C#8
*I
+AR2
TAR2 #TEMP10
TAR1 #TEMP4
LAR1 #TEMP9
LAR2 #TEMP10
L B [AR1,P#0.0]
L B [AR2,P#0.0]
-I
T B [AR1,P#0.0]
L DW#16#0
T #TEMP0
L MB 101
T #TEMP1
L MB 102
T #TEMP2
L #TEMP4
LAR1
JU M006
M012: L #TEMP15
INC 1
T #TEMP15
+AR1 P#1.0
L B [AR1,P#0.0]
T #TEMP7
L P#M 100.0
LAR2
L #TEMP7
L C#8
*I
+AR2
TAR2 #TEMP9
+AR1 P#1.0
L B [AR1,P#0.0]
T #TEMP8
L P#M 100.0
LAR2
L #TEMP8
L C#8
*I
+AR2
TAR2 #TEMP10
TAR1 #TEMP4
LAR1 #TEMP9
LAR2 #TEMP10
L B [AR1,P#0.0]
L B [AR2,P#0.0]
==I
JCN M013
JU M014
M013: L P#DBX 0.0
LAR1
T #TEMP4
L B#16#0
T #TEMP6
JU M006
M014: L #TEMP4
LAR1
L #TEMP13
L L#1
+I
T #TEMP13
JU M006
M006: L #TEMP0
T MB 100
L #TEMP1
T MB 101
L #TEMP2
T MB 102
+AR1 P#1.0
L #TEMP6
+ 1
T #TEMP6
JU M005
M010: L P#DBX 0.0
LAR1
L 0
T #TEMP6
TAR1 #TEMP4
M005: TAR1 #TEMP4
CLR
= #TEMP16
L #TEMP13
L L#20
==I
S #TEMP16
L #TEMP15
==I
A #TEMP16
JC M017
L #TEMP13
L L#20
<I
S #TEMP16
L #TEMP15
==I
A #TEMP16
JC M018
JU M019
M017: SET
= #TEMP14
JU M016
M018: CLR
= #TEMP14
JU M016
M019: CLR
O #TEMP14
= #RET_VAL
JU M015
M016: CLR
O #TEMP14
= #RET_VALThe code is quite voluminous and a person unfamiliar with the STL may find it difficult. It makes no sense to analyze each instruction within the framework of this article, you can read the instructions and capabilities of the STL language in detail in the corresponding manual: . Here I will give the same code after processing - renaming labels and variables and adding comments describing the algorithm of work and some constructions of the STL language. I note right away that the block under consideration implements a virtual machine that executes some bytecode located in the DB100 block, the contents of which are known to us. Virtual machine instructions are 1 byte of opcode and argument bytes, one byte for each argument. All the considered instructions have two arguments, I designated their values in the comments as X and Y.
Code after processing]
# Инициализация различных переменных
L B#16#0
T #CHECK_N # Счетчик успешно пройденных проверок
T #COUNTER_N # Счетчик общего количества проверок
L P#DBX 0.0
T #POINTER # Указатель на текущую инструкцию
CLR
= #PRE_RET_VAL
# Основной цикл работы интерпретатора байт-кода
LOOP: L #POINTER
LAR1
OPN DB 100
L DBLG
TAR1
<=D # Проверка выхода указателя за пределы программы
JC FINISH
L DW#16#0
T #REG0
L #TEMP6
L W#16#0
<>I
JC M00d
L P#DBX 0.0
LAR1
# Конструкция switch - case для обработки различных опкодов
M00d: L B [AR1,P#0.0]
T #OPCODE
L W#16#1
==I
JC OPCODE_1
L #OPCODE
L W#16#2
==I
JC OPCODE_2
L #OPCODE
L W#16#3
==I
JC OPCODE_3
L #OPCODE
L W#16#4
==I
JC OPCODE_4
L #OPCODE
L W#16#5
==I
JC OPCODE_5
L #OPCODE
L W#16#6
==I
JC OPCODE_6
JU OPCODE_OTHER
# Обработчик опкода 01: загрузка значения из DB101[X] в регистр Y
# OP01(X, Y): REG[Y] = DB101[X]
OPCODE_1: +AR1 P#1.0
L P#DBX 0.0
LAR2
L B [AR1,P#0.0] # Загрузка аргумента X (индекс в DB101)
L C#8
*I
+AR2
+AR1 P#1.0
L B [AR1,P#0.0] # Загрузка аргумента Y (индекс регистра)
JL M003 # Аналог switch - case на основе значения Y
JU M001 # для выбора необходимого регистра для записи.
JU M002 # Подобные конструкции используются и в других
JU M004 # операциях ниже для аналогичных целей
M003: JU LOOPEND
M001: OPN DB 101
L B [AR2,P#0.0]
T #REG0 # Запись значения DB101[X] в REG[0]
JU PRE_LOOPEND
M002: OPN DB 101
L B [AR2,P#0.0]
T #REG1 # Запись значения DB101[X] в REG[1]
JU PRE_LOOPEND
M004: OPN DB 101
L B [AR2,P#0.0]
T #REG2 # Запись значения DB101[X] в REG[2]
JU PRE_LOOPEND
# Обработчик опкода 02: загрузка значения X в регистр Y
# OP02(X, Y): REG[Y] = X
OPCODE_2: +AR1 P#1.0
L B [AR1,P#0.0]
T #TEMP3
+AR1 P#1.0
L B [AR1,P#0.0]
JL M009
JU M00b
JU M00a
JU M00c
M009: JU LOOPEND
M00b: L #TEMP3
T #REG0
JU PRE_LOOPEND
M00a: L #TEMP3
T #REG1
JU PRE_LOOPEND
M00c: L #TEMP3
T #REG2
JU PRE_LOOPEND
# Опкод 03 не используется в программе, поэтому пропустим его
...
# Обработчик опкода 04: сравнение регистров X и Y
# OP04(X, Y): REG[0] = 0; REG[X] = (REG[X] == REG[Y])
OPCODE_4: +AR1 P#1.0
L B [AR1,P#0.0]
T #TEMP7 # первый аргумент - X
L P#M 100.0
LAR2
L #TEMP7
L C#8
*I
+AR2
TAR2 #TEMP9 # REG[X]
+AR1 P#1.0
L B [AR1,P#0.0]
T #TEMP8
L P#M 100.0
LAR2
L #TEMP8
L C#8
*I
+AR2
TAR2 #TEMP10 # REG[Y]
TAR1 #POINTER
LAR1 #TEMP9 # REG[X]
LAR2 #TEMP10 # REG[Y]
L B [AR1,P#0.0]
L B [AR2,P#0.0]
AW
INVI
T #TEMP12 # ~(REG[Y] & REG[X])
L B [AR1,P#0.0]
L B [AR2,P#0.0]
OW
L #TEMP12
AW # (~(REG[Y] & REG[X])) & (REG[Y] | REG[X]) - аналог проверки на равенство
T B [AR1,P#0.0]
L DW#16#0
T #REG0
L MB 101
T #REG1
L MB 102
T #REG2
L #POINTER
LAR1
JU PRE_LOOPEND
# Обработчик опкода 05: вычитание регистра Y из X
# OP05(X, Y): REG[0] = 0; REG[X] = REG[X] - REG[Y]
OPCODE_5: +AR1 P#1.0
L B [AR1,P#0.0]
T #TEMP7
L P#M 100.0
LAR2
L #TEMP7
L C#8
*I
+AR2
TAR2 #TEMP9 # REG[X]
+AR1 P#1.0
L B [AR1,P#0.0]
T #TEMP8
L P#M 100.0
LAR2
L #TEMP8
L C#8
*I
+AR2
TAR2 #TEMP10 # REG[Y]
TAR1 #POINTER
LAR1 #TEMP9
LAR2 #TEMP10
L B [AR1,P#0.0]
L B [AR2,P#0.0]
-I # ACCU1 = ACCU2 - ACCU1, REG[X] - REG[Y]
T B [AR1,P#0.0]
L DW#16#0
T #REG0
L MB 101
T #REG1
L MB 102
T #REG2
L #POINTER
LAR1
JU PRE_LOOPEND
# Обработчик опкода 06: инкремент #CHECK_N при равенстве регистров X и Y
# OP06(X, Y): #CHECK_N += (1 if REG[X] == REG[Y] else 0)
OPCODE_6: L #COUNTER_N
INC 1
T #COUNTER_N
+AR1 P#1.0
L B [AR1,P#0.0]
T #TEMP7 # REG[X]
L P#M 100.0
LAR2
L #TEMP7
L C#8
*I
+AR2
TAR2 #TEMP9 # REG[X]
+AR1 P#1.0
L B [AR1,P#0.0]
T #TEMP8
L P#M 100.0
LAR2
L #TEMP8
L C#8
*I
+AR2
TAR2 #TEMP10 # REG[Y]
TAR1 #POINTER
LAR1 #TEMP9 # REG[Y]
LAR2 #TEMP10 # REG[X]
L B [AR1,P#0.0]
L B [AR2,P#0.0]
==I
JCN M013
JU M014
M013: L P#DBX 0.0
LAR1
T #POINTER
L B#16#0
T #TEMP6
JU PRE_LOOPEND
M014: L #POINTER
LAR1
# Инкремент значения #CHECK_N
L #CHECK_N
L L#1
+I
T #CHECK_N
JU PRE_LOOPEND
PRE_LOOPEND: L #REG0
T MB 100
L #REG1
T MB 101
L #REG2
T MB 102
+AR1 P#1.0
L #TEMP6
+ 1
T #TEMP6
JU LOOPEND
OPCODE_OTHER: L P#DBX 0.0
LAR1
L 0
T #TEMP6
TAR1 #POINTER
LOOPEND: TAR1 #POINTER
CLR
= #TEMP16
L #CHECK_N
L L#20
==I
S #TEMP16
L #COUNTER_N
==I
A #TEMP16
# Все проверки пройдены, если #CHECK_N == #COUNTER_N == 20
JC GOOD
L #CHECK_N
L L#20
<I
S #TEMP16
L #COUNTER_N
==I
A #TEMP16
JC FAIL
JU M019
GOOD: SET
= #PRE_RET_VAL
JU FINISH
FAIL: CLR
= #PRE_RET_VAL
JU FINISH
M019: CLR
O #PRE_RET_VAL
= #RET_VAL
JU LOOP
FINISH: CLR
O #PRE_RET_VAL
= #RET_VALHaving got an idea about the instructions of the virtual machine, let's write a small disassembler to parse the bytecode in the DB100 block:
import string
alph = string.ascii_letters + string.digits
with open('DB100.bin', 'rb') as f:
m = f.read()
pc = 0
while pc < len(m):
op = m[pc]
if op == 1:
print('R{} = DB101[{}]'.format(m[pc + 2], m[pc + 1]))
pc += 3
elif op == 2:
c = chr(m[pc + 1])
c = c if c in alph else '?'
print('R{} = {:02x} ({})'.format(m[pc + 2], m[pc + 1], c))
pc += 3
elif op == 4:
print('R0 = 0; R{} = (R{} == R{})'.format(
m[pc + 1], m[pc + 1], m[pc + 2]))
pc += 3
elif op == 5:
print('R0 = 0; R{} = R{} - R{}'.format(
m[pc + 1], m[pc + 1], m[pc + 2]))
pc += 3
elif op == 6:
print('CHECK (R{} == R{})n'.format(
m[pc + 1], m[pc + 2]))
pc += 3
else:
print('unk opcode {}'.format(op))
breakAs a result, we get the following virtual machine code:
VM Code
R1 = DB101[0]
R2 = 6e (n)
R0 = 0; R1 = (R1 == R2)
CHECK (R1 == R0)
R1 = DB101[1]
R2 = 10 (?)
R0 = 0; R1 = R1 - R2
R2 = 20 (?)
R0 = 0; R1 = R1 - R2
CHECK (R1 == R0)
R1 = DB101[2]
R2 = 77 (w)
R0 = 0; R1 = (R1 == R2)
CHECK (R1 == R0)
R1 = DB101[3]
R2 = 0a (?)
R0 = 0; R1 = R1 - R2
R2 = 16 (?)
R0 = 0; R1 = R1 - R2
CHECK (R1 == R0)
R1 = DB101[4]
R2 = 75 (u)
R0 = 0; R1 = (R1 == R2)
CHECK (R1 == R0)
R1 = DB101[5]
R2 = 0a (?)
R0 = 0; R1 = R1 - R2
R2 = 16 (?)
R0 = 0; R1 = R1 - R2
CHECK (R1 == R0)
R1 = DB101[6]
R2 = 34 (4)
R0 = 0; R1 = (R1 == R2)
CHECK (R1 == R0)
R1 = DB101[7]
R2 = 26 (?)
R0 = 0; R1 = R1 - R2
R2 = 4c (L)
R0 = 0; R1 = R1 - R2
CHECK (R1 == R0)
R1 = DB101[8]
R2 = 33 (3)
R0 = 0; R1 = (R1 == R2)
CHECK (R1 == R0)
R1 = DB101[9]
R2 = 0a (?)
R0 = 0; R1 = R1 - R2
R2 = 16 (?)
R0 = 0; R1 = R1 - R2
CHECK (R1 == R0)
R1 = DB101[10]
R2 = 37 (7)
R0 = 0; R1 = (R1 == R2)
CHECK (R1 == R0)
R1 = DB101[11]
R2 = 22 (?)
R0 = 0; R1 = R1 - R2
R2 = 46 (F)
R0 = 0; R1 = R1 - R2
CHECK (R1 == R0)
R1 = DB101[12]
R2 = 33 (3)
R0 = 0; R1 = (R1 == R2)
CHECK (R1 == R0)
R1 = DB101[13]
R2 = 0a (?)
R0 = 0; R1 = R1 - R2
R2 = 16 (?)
R0 = 0; R1 = R1 - R2
CHECK (R1 == R0)
R1 = DB101[14]
R2 = 6d (m)
R0 = 0; R1 = (R1 == R2)
CHECK (R1 == R0)
R1 = DB101[15]
R2 = 11 (?)
R0 = 0; R1 = R1 - R2
R2 = 23 (?)
R0 = 0; R1 = R1 - R2
CHECK (R1 == R0)
R1 = DB101[16]
R2 = 35 (5)
R0 = 0; R1 = (R1 == R2)
CHECK (R1 == R0)
R1 = DB101[17]
R2 = 12 (?)
R0 = 0; R1 = R1 - R2
R2 = 25 (?)
R0 = 0; R1 = R1 - R2
CHECK (R1 == R0)
R1 = DB101[18]
R2 = 33 (3)
R0 = 0; R1 = (R1 == R2)
CHECK (R1 == R0)
R1 = DB101[19]
R2 = 26 (?)
R0 = 0; R1 = R1 - R2
R2 = 4c (L)
R0 = 0; R1 = R1 - R2
CHECK (R1 == R0)As you can see, this program simply checks each character from DB101 for equality to a certain value. The final line for passing all checks: n0w u 4r3 7h3 m4573r. If this line is placed in the DB101 block, the PLC manual control will be activated and it will be possible to blow up or deflate the balloon.
That's all! Alexey demonstrated a high level of knowledge worthy of an industrial ninja 🙂 We sent memorable prizes to the winner. Many thanks to all participants!
Source: habr.com
