In today's article I want to share with you a new project. This time it is a touch switch with a glass panel. The device is compact, with dimensions of 42x42mm (standard glass panel has dimensions of 80x80mm). The history of this device began a long time ago, about a year ago.
The first options were on the atmega328 microcontroller, but in the end it all ended with the nRF52832 microcontroller.
The touch part of the device works on TTP223 chips. Both sensors serve one interrupt. Powered by a CR2477 battery, via a boost converter based on the TPS610981 chip | .
The device implements a power-off circuit on field-effect transistors. After pressing the button, the microcontroller itself intercepts power management and then the button can be used for service modes (in my case, this is pairing with other devices, turning off the power and resetting to factory settings (factory reset)).
There are 2 rgb LEDs for status indications and service modes. A piezo emitter has also been added to simulate a click when touching the touch buttons and sound indication of service modes. The LEDs and the piezo emitter can be turned on and off at the user's request. This is done through the smart home controller, by sending commands to technical sensors, the user can also change the intervals for sending the battery charge and the signal level through the smart home controller. In my case it is .
Consumption in transmit mode 7mA (250kbps, 10ms), consumption in sleep 40uA, consumption in off state less than 1uA (= boost converter consumption in "idle" mode). Output rx, tx, swd connector for programming. A 2x3p miniature connector with a pitch of 1.27 is used. A special adapter is made for programming.
As always, the operation of the device is based on the protocol . This touch switch is planned to be used in the roller blind control system. But in general, the application is limited only by your imagination. For example, my son (7 years old) has already made 3 orders for the version of the switch: to turn on and off the light in the toilet with a bath (it will be mounted low from the floor), to turn on the light in a long and dark corridor when traveling to the toilet with a bath, and one more as bedside, to quickly turn on the light in your room so that the monsters scatter.
The case was traditionally printed on an SLA printer, the device is miniature, the case turned out to be small, the use of this printing technology is justified.
View printed model
Magnets are glued into the case and the battery cover.
Videos with tests of this device:
For those who want to repeat:
The code of the switch test program in the roller blind control system for the Arduino IDE
Arduino Wiring
int8_t timer_status = 0;
boolean sens_flag1 = 0;
boolean sens_flag2 = 0;
boolean switch_a = 0;
boolean switch_b = 0;
uint16_t temp;
float vcc;
int battery;
int old_battery;
uint32_t oldmillis;
uint32_t newmillis;
uint32_t interrupt_time;
uint32_t SLEEP_TIME = 7000;
uint32_t SLEEP_TIME_W;
uint32_t SLEEP_TIME_W2;
int NrfRSSI;
uint16_t NrfRSSI2;
boolean wait_off;
//#define MY_DEBUG
#define MY_DISABLED_SERIAL
#define MY_RADIO_NRF5_ESB
#define MY_PASSIVE_NODE
#define MY_NODE_ID 120
#define MY_PARENT_NODE_ID 0
#define MY_PARENT_NODE_IS_STATIC
#define MY_TRANSPORT_UPLINK_CHECK_DISABLED
#define POWER_CHILD_ID 110
#define UP_POWER_SWITCH_ID 1
#define DOWN_POWER_SWITCH_ID 2
#define CHILD_ID_nRF52_RSSI_RX 3
#define BAT_COOF 0.0092957746478873
#define BAT_MIN 200
#define BAT_MAX 290
#include <MySensors.h>
MyMessage upMsg(UP_POWER_SWITCH_ID, V_STATUS);
MyMessage downMsg(DOWN_POWER_SWITCH_ID, V_STATUS);
MyMessage powerMsg(POWER_CHILD_ID, V_VAR1);
MyMessage msgRF52RssiReceiv(CHILD_ID_nRF52_RSSI_RX, V_VAR1);
void preHwInit() {
pinMode(31, OUTPUT); //power management pin
digitalWrite(31, HIGH);
delay(3000);
pinMode(3, INPUT); // on off mode button
pinMode(25, OUTPUT); // sens1 led
pinMode(26, OUTPUT); // sens1 led
pinMode(27, OUTPUT); // sens1 led
pinMode(6, OUTPUT); // sens21 led
pinMode(7, OUTPUT); // sens2 led
pinMode(8, OUTPUT); // sens2 led
pinMode(28, OUTPUT); // bizzer
pinMode(2, INPUT); // common interrupt for touch sensors
pinMode(9, INPUT); // touch sensors1
pinMode(10, INPUT); //touch sensors2
pinMode(29, INPUT); // battery
digitalWrite(28, LOW);
digitalWrite(27, HIGH);
digitalWrite(26, HIGH);
digitalWrite(25, HIGH);
digitalWrite(6, HIGH);
digitalWrite(7, HIGH);
digitalWrite(8, HIGH);
}
void before()
{
NRF_POWER->DCDCEN = 1;
analogReadResolution(12);
disableNfc();
turnOffAdc();
digitalWrite(25, LOW);
digitalWrite(6, LOW);
wait(200);
digitalWrite(25, HIGH);
digitalWrite(6, HIGH);
wait(100);
playSound0();
wait(100);
digitalWrite(25, LOW);
digitalWrite(6, LOW);
wait(200);
digitalWrite(25, HIGH);
digitalWrite(6, HIGH);
wait(3000);
digitalWrite(27, LOW);
digitalWrite(8, LOW);
wait(200);
digitalWrite(27, HIGH);
digitalWrite(8, HIGH);
wait(400);
digitalWrite(6, LOW);
digitalWrite(25, LOW);
wait(200);
digitalWrite(6, HIGH);
digitalWrite(25, HIGH);
wait(400);
digitalWrite(26, LOW);
digitalWrite(7, LOW);
wait(200);
digitalWrite(26, HIGH);
digitalWrite(7, HIGH);
wait(1000);
digitalWrite(26, LOW);
digitalWrite(7, LOW);
}
void setup()
{
digitalWrite(26, HIGH);
digitalWrite(7, HIGH);
wait(50);
playSound();
wait(2000);
readBatLev();
wait(200);
SLEEP_TIME_W = SLEEP_TIME;
}
void presentation()
{
sendSketchInfo("EFEKTA ON|OFF NODE 2CH", "1.0");
wait(100);
present(POWER_CHILD_ID, S_CUSTOM, "BATTERY DATA");
wait(100);
present(UP_POWER_SWITCH_ID, S_BINARY, "UP SWITCH");
wait(100);
present(DOWN_POWER_SWITCH_ID, S_BINARY, "DOWN SWITCH");
}
void loop()
{
if (sens_flag1 == 0 && sens_flag2 == 0) {
if (switch_a == 0 && switch_b == 0) {
timer_status = sleep(digitalPinToInterrupt(2), RISING, digitalPinToInterrupt(3), RISING, 3600000, false);
wait_off = 1;
} else {
//oldmillis = millis();
timer_status = sleep(digitalPinToInterrupt(2), RISING, digitalPinToInterrupt(3), RISING, SLEEP_TIME_W, false);
wait_off = 0;
}
}
if (timer_status == 3) {
wait(100);
digitalWrite(27, LOW);
digitalWrite(8, LOW);
wait(2000);
digitalWrite(27, HIGH);
digitalWrite(8, HIGH);
wait(100);
digitalWrite(31, LOW);
}
if (timer_status == 2) {
if (digitalRead(9) == HIGH && sens_flag1 == 0 && switch_b == 0) {
sens_flag1 = 1;
if (switch_a == 0) {
oldmillis = millis();
SLEEP_TIME_W = SLEEP_TIME;
switch_a = 1;
digitalWrite(6, LOW);
wait(10);
playSound1();
wait(20);
playSound2();
wait(50);
send(upMsg.set(switch_a));
wait(200);
} else {
switch_a = 0;
digitalWrite(6, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(upMsg.set(switch_a));
wait(200);
}
}
if (digitalRead(10) == HIGH && sens_flag2 == 0 && switch_a == 0) {
sens_flag2 = 1;
if (switch_b == 0) {
oldmillis = millis();
SLEEP_TIME_W = SLEEP_TIME;
switch_b = 1;
digitalWrite(25, LOW);
wait(10);
playSound1();
wait(20);
playSound2();
wait(50);
send(downMsg.set(switch_b));
wait(200);
} else {
switch_b = 0;
digitalWrite(25, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(downMsg.set(switch_b));
wait(200);
}
}
if (digitalRead(9) == LOW && sens_flag1 == 1) {
sens_flag1 = 0;
}
if (digitalRead(10) == LOW && sens_flag2 == 1) {
sens_flag2 = 0;
}
if (switch_a == 1 || switch_b == 1) {
if (wait_off == 0) {
newmillis = millis();
wait(10);
SLEEP_TIME_W2 = SLEEP_TIME_W;
wait(10);
interrupt_time = newmillis - oldmillis;
wait(10);
SLEEP_TIME_W = SLEEP_TIME_W2 - interrupt_time;
wait(10);
Serial.print("WAS IN A SLEEP: ");
Serial.print(newmillis - oldmillis);
Serial.println(" MILLISECONDS");
if (SLEEP_TIME_W < 1000) {
if (switch_a == 1) {
switch_a = 0;
digitalWrite(6, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(upMsg.set(switch_a));
wait(200);
}
if (switch_b == 1) {
switch_b = 0;
digitalWrite(25, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(downMsg.set(switch_b));
wait(200);
}
SLEEP_TIME_W = SLEEP_TIME;
wait(50);
}
Serial.println(SLEEP_TIME);
Serial.println(SLEEP_TIME_W);
Serial.println(SLEEP_TIME_W2);
Serial.print("GO TO SLEEP FOR: ");
Serial.print(SLEEP_TIME_W);
Serial.println(" MILLISECONDS");
}
oldmillis = millis();
}
}
if (timer_status == -1) {
if (switch_a == 1 || switch_b == 1) {
if (switch_a == 1) {
switch_a = 0;
digitalWrite(6, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(upMsg.set(switch_a));
wait(200);
}
if (switch_b == 1) {
switch_b = 0;
digitalWrite(25, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(downMsg.set(switch_b));
wait(200);
}
} else {
readBatLev();
}
}
}
void disableNfc() {
NRF_NFCT->TASKS_DISABLE = 1;
NRF_NVMC->CONFIG = 1;
NRF_UICR->NFCPINS = 0;
NRF_NVMC->CONFIG = 0;
}
void turnOffAdc() {
if (NRF_SAADC->ENABLE) {
NRF_SAADC->TASKS_STOP = 1;
while (NRF_SAADC->EVENTS_STOPPED) {}
NRF_SAADC->ENABLE = 0;
while (NRF_SAADC->ENABLE) {}
}
}
void myTone(uint32_t j, uint32_t k) {
j = 500000 / j;
k += millis();
while (k > millis()) {
digitalWrite(28, HIGH); delayMicroseconds(j);
digitalWrite(28, LOW ); delayMicroseconds(j);
}
}
void playSound0() {
myTone(1300, 50);
wait(20);
myTone(1300, 50);
wait(50);
}
void playSound() {
myTone(700, 30);
wait(10);
myTone(700, 30);
wait(10);
myTone(700, 30);
wait(50);
}
void playSound1() {
myTone(200, 10);
wait(10);
myTone(400, 5);
wait(30);
}
void playSound2() {
myTone(400, 10);
wait(10);
myTone(200, 5);
wait(30);
}
void readBatLev() {
temp = analogRead(29);
vcc = temp * 0.0033 * 100;
battery = map((int)vcc, BAT_MIN, BAT_MAX, 0, 100);
if (battery < 0) {
battery = 0;
}
if (battery > 100) {
battery = 100;
}
sendBatteryLevel(battery, 1);
wait(2000, C_INTERNAL, I_BATTERY_LEVEL);
send(powerMsg.set(temp));
wait(200);
NrfRSSI = transportGetReceivingRSSI();
NrfRSSI2 = map(NrfRSSI, -85, -40, 0, 100);
if (NrfRSSI2 < 0) {
NrfRSSI2 = 0;
}
if (NrfRSSI2 > 100) {
NrfRSSI2 = 100;
}
send(msgRF52RssiReceiv.set(NrfRSSI2));
wait(200);
}Corpus files in stl -
Gerber PCB files -
For questions about this development, about the difficulties in your developments on arduino and Mysensors, they will always come to the rescue in our telegram chat - .
Source: habr.com