Tänases artiklis tahan teiega jagada uut projekti. Seekord on tegemist klaaspaneeliga puutelülitiga. Seade on kompaktne, mõõtmetega 42x42mm (standardsete klaaspaneelide mõõtmed on 80x80mm). Selle seadme ajalugu algas kaua aega tagasi, umbes aasta tagasi.
Esimesed valikud olid atmega328 mikrokontrolleril, kuid lõpuks lõppes kõik nRF52832 mikrokontrolleriga.
Seadme puutetundlik osa töötab TTP223 kiipidega. Mõlemat andurit teenindab üks katkestus. Toiteallikaks on CR2477 aku, TPS610981 kiibil oleva võimendusmuunduri kaudu | .
Seade rakendab väljatransistoride abil väljalülitusahelat. Pärast nupu vajutamist võtab mikrokontroller ise kinni toite juhtimise ja seejärel saab nuppu kasutada teenindusrežiimide jaoks (minu puhul on see teiste seadmetega sidumine, toite väljalülitamine ja tehaseseadetele lähtestamine).
Olekute ja teenindusrežiimide näitamiseks on 2 rgb LED-i. Lisatud on ka pieso-emitter, mis simuleerib puutenuppude puudutamisel klõpsamist ja teenindusrežiimide helisignaali. LED-e ja pieso-emitterit saab kasutaja äranägemise järgi sisse ja välja lülitada. See toimub targa kodu kontrolleri kaudu tehnilistele anduritele käskude saates, samuti saab kasutaja muuta aku laetuse ja signaali taseme saatmise intervalle ka läbi targa kodu kontrolleri. Minu puhul on .
Tarbimine edastusrežiimis on 7 mA (250 kbit, 10 ms), tarbimine unerežiimis 40 µA, tarbimine väljalülitatud olekus on alla 1 µA (=võimendusmuunduri tarbimine jõuderežiimis). Programmeerimiseks on kaasas Rx, tx, swd pistik. Kasutatakse miniatuurset 2x3p pistikut sammuga 1.27. Programmeerimiseks valmistatakse spetsiaalne adapter.
Nagu ikka, toimub seadme töö protokolli alusel . Seda puutelülitit on plaanis kasutada ruloode juhtimissüsteemis. Kuid üldiselt piirab rakendust ainult teie kujutlusvõime. Näiteks mu poeg (7-aastane) on teinud juba 3 tellimust lüliti versioonide jaoks: vanniga tualetis valguse sisse-välja lülitamine (see paigaldatakse põrandast madalale), valguse sisselülitamine pikk ja pime koridor, kui reisite vanniga tualetti, ja teine voodikohaks, et oma toas valgus kiiresti põlema panna, et koletised minema jookseks.
Korpus trükiti traditsiooniliselt SLA-printerile, seade on miniatuurne, korpus osutus väikeseks, selle printimistehnoloogia kasutamine on õigustatud.
Vaata trükitud mudelit
Magnetid on liimitud korpusesse ja akupesa kaanesse.
Videod selle seadme testidega:
Neile, kes soovivad korrata:
Testige Arduino IDE ruloode juhtimissüsteemi lüliti programmikoodi
Arduino juhtmestik
int8_t timer_status = 0;
boolean sens_flag1 = 0;
boolean sens_flag2 = 0;
boolean switch_a = 0;
boolean switch_b = 0;
uint16_t temp;
float vcc;
int battery;
int old_battery;
uint32_t oldmillis;
uint32_t newmillis;
uint32_t interrupt_time;
uint32_t SLEEP_TIME = 7000;
uint32_t SLEEP_TIME_W;
uint32_t SLEEP_TIME_W2;
int NrfRSSI;
uint16_t NrfRSSI2;
boolean wait_off;
//#define MY_DEBUG
#define MY_DISABLED_SERIAL
#define MY_RADIO_NRF5_ESB
#define MY_PASSIVE_NODE
#define MY_NODE_ID 120
#define MY_PARENT_NODE_ID 0
#define MY_PARENT_NODE_IS_STATIC
#define MY_TRANSPORT_UPLINK_CHECK_DISABLED
#define POWER_CHILD_ID 110
#define UP_POWER_SWITCH_ID 1
#define DOWN_POWER_SWITCH_ID 2
#define CHILD_ID_nRF52_RSSI_RX 3
#define BAT_COOF 0.0092957746478873
#define BAT_MIN 200
#define BAT_MAX 290
#include <MySensors.h>
MyMessage upMsg(UP_POWER_SWITCH_ID, V_STATUS);
MyMessage downMsg(DOWN_POWER_SWITCH_ID, V_STATUS);
MyMessage powerMsg(POWER_CHILD_ID, V_VAR1);
MyMessage msgRF52RssiReceiv(CHILD_ID_nRF52_RSSI_RX, V_VAR1);
void preHwInit() {
pinMode(31, OUTPUT); //power management pin
digitalWrite(31, HIGH);
delay(3000);
pinMode(3, INPUT); // on off mode button
pinMode(25, OUTPUT); // sens1 led
pinMode(26, OUTPUT); // sens1 led
pinMode(27, OUTPUT); // sens1 led
pinMode(6, OUTPUT); // sens21 led
pinMode(7, OUTPUT); // sens2 led
pinMode(8, OUTPUT); // sens2 led
pinMode(28, OUTPUT); // bizzer
pinMode(2, INPUT); // common interrupt for touch sensors
pinMode(9, INPUT); // touch sensors1
pinMode(10, INPUT); //touch sensors2
pinMode(29, INPUT); // battery
digitalWrite(28, LOW);
digitalWrite(27, HIGH);
digitalWrite(26, HIGH);
digitalWrite(25, HIGH);
digitalWrite(6, HIGH);
digitalWrite(7, HIGH);
digitalWrite(8, HIGH);
}
void before()
{
NRF_POWER->DCDCEN = 1;
analogReadResolution(12);
disableNfc();
turnOffAdc();
digitalWrite(25, LOW);
digitalWrite(6, LOW);
wait(200);
digitalWrite(25, HIGH);
digitalWrite(6, HIGH);
wait(100);
playSound0();
wait(100);
digitalWrite(25, LOW);
digitalWrite(6, LOW);
wait(200);
digitalWrite(25, HIGH);
digitalWrite(6, HIGH);
wait(3000);
digitalWrite(27, LOW);
digitalWrite(8, LOW);
wait(200);
digitalWrite(27, HIGH);
digitalWrite(8, HIGH);
wait(400);
digitalWrite(6, LOW);
digitalWrite(25, LOW);
wait(200);
digitalWrite(6, HIGH);
digitalWrite(25, HIGH);
wait(400);
digitalWrite(26, LOW);
digitalWrite(7, LOW);
wait(200);
digitalWrite(26, HIGH);
digitalWrite(7, HIGH);
wait(1000);
digitalWrite(26, LOW);
digitalWrite(7, LOW);
}
void setup()
{
digitalWrite(26, HIGH);
digitalWrite(7, HIGH);
wait(50);
playSound();
wait(2000);
readBatLev();
wait(200);
SLEEP_TIME_W = SLEEP_TIME;
}
void presentation()
{
sendSketchInfo("EFEKTA ON|OFF NODE 2CH", "1.0");
wait(100);
present(POWER_CHILD_ID, S_CUSTOM, "BATTERY DATA");
wait(100);
present(UP_POWER_SWITCH_ID, S_BINARY, "UP SWITCH");
wait(100);
present(DOWN_POWER_SWITCH_ID, S_BINARY, "DOWN SWITCH");
}
void loop()
{
if (sens_flag1 == 0 && sens_flag2 == 0) {
if (switch_a == 0 && switch_b == 0) {
timer_status = sleep(digitalPinToInterrupt(2), RISING, digitalPinToInterrupt(3), RISING, 3600000, false);
wait_off = 1;
} else {
//oldmillis = millis();
timer_status = sleep(digitalPinToInterrupt(2), RISING, digitalPinToInterrupt(3), RISING, SLEEP_TIME_W, false);
wait_off = 0;
}
}
if (timer_status == 3) {
wait(100);
digitalWrite(27, LOW);
digitalWrite(8, LOW);
wait(2000);
digitalWrite(27, HIGH);
digitalWrite(8, HIGH);
wait(100);
digitalWrite(31, LOW);
}
if (timer_status == 2) {
if (digitalRead(9) == HIGH && sens_flag1 == 0 && switch_b == 0) {
sens_flag1 = 1;
if (switch_a == 0) {
oldmillis = millis();
SLEEP_TIME_W = SLEEP_TIME;
switch_a = 1;
digitalWrite(6, LOW);
wait(10);
playSound1();
wait(20);
playSound2();
wait(50);
send(upMsg.set(switch_a));
wait(200);
} else {
switch_a = 0;
digitalWrite(6, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(upMsg.set(switch_a));
wait(200);
}
}
if (digitalRead(10) == HIGH && sens_flag2 == 0 && switch_a == 0) {
sens_flag2 = 1;
if (switch_b == 0) {
oldmillis = millis();
SLEEP_TIME_W = SLEEP_TIME;
switch_b = 1;
digitalWrite(25, LOW);
wait(10);
playSound1();
wait(20);
playSound2();
wait(50);
send(downMsg.set(switch_b));
wait(200);
} else {
switch_b = 0;
digitalWrite(25, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(downMsg.set(switch_b));
wait(200);
}
}
if (digitalRead(9) == LOW && sens_flag1 == 1) {
sens_flag1 = 0;
}
if (digitalRead(10) == LOW && sens_flag2 == 1) {
sens_flag2 = 0;
}
if (switch_a == 1 || switch_b == 1) {
if (wait_off == 0) {
newmillis = millis();
wait(10);
SLEEP_TIME_W2 = SLEEP_TIME_W;
wait(10);
interrupt_time = newmillis - oldmillis;
wait(10);
SLEEP_TIME_W = SLEEP_TIME_W2 - interrupt_time;
wait(10);
Serial.print("WAS IN A SLEEP: ");
Serial.print(newmillis - oldmillis);
Serial.println(" MILLISECONDS");
if (SLEEP_TIME_W < 1000) {
if (switch_a == 1) {
switch_a = 0;
digitalWrite(6, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(upMsg.set(switch_a));
wait(200);
}
if (switch_b == 1) {
switch_b = 0;
digitalWrite(25, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(downMsg.set(switch_b));
wait(200);
}
SLEEP_TIME_W = SLEEP_TIME;
wait(50);
}
Serial.println(SLEEP_TIME);
Serial.println(SLEEP_TIME_W);
Serial.println(SLEEP_TIME_W2);
Serial.print("GO TO SLEEP FOR: ");
Serial.print(SLEEP_TIME_W);
Serial.println(" MILLISECONDS");
}
oldmillis = millis();
}
}
if (timer_status == -1) {
if (switch_a == 1 || switch_b == 1) {
if (switch_a == 1) {
switch_a = 0;
digitalWrite(6, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(upMsg.set(switch_a));
wait(200);
}
if (switch_b == 1) {
switch_b = 0;
digitalWrite(25, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(downMsg.set(switch_b));
wait(200);
}
} else {
readBatLev();
}
}
}
void disableNfc() {
NRF_NFCT->TASKS_DISABLE = 1;
NRF_NVMC->CONFIG = 1;
NRF_UICR->NFCPINS = 0;
NRF_NVMC->CONFIG = 0;
}
void turnOffAdc() {
if (NRF_SAADC->ENABLE) {
NRF_SAADC->TASKS_STOP = 1;
while (NRF_SAADC->EVENTS_STOPPED) {}
NRF_SAADC->ENABLE = 0;
while (NRF_SAADC->ENABLE) {}
}
}
void myTone(uint32_t j, uint32_t k) {
j = 500000 / j;
k += millis();
while (k > millis()) {
digitalWrite(28, HIGH); delayMicroseconds(j);
digitalWrite(28, LOW ); delayMicroseconds(j);
}
}
void playSound0() {
myTone(1300, 50);
wait(20);
myTone(1300, 50);
wait(50);
}
void playSound() {
myTone(700, 30);
wait(10);
myTone(700, 30);
wait(10);
myTone(700, 30);
wait(50);
}
void playSound1() {
myTone(200, 10);
wait(10);
myTone(400, 5);
wait(30);
}
void playSound2() {
myTone(400, 10);
wait(10);
myTone(200, 5);
wait(30);
}
void readBatLev() {
temp = analogRead(29);
vcc = temp * 0.0033 * 100;
battery = map((int)vcc, BAT_MIN, BAT_MAX, 0, 100);
if (battery < 0) {
battery = 0;
}
if (battery > 100) {
battery = 100;
}
sendBatteryLevel(battery, 1);
wait(2000, C_INTERNAL, I_BATTERY_LEVEL);
send(powerMsg.set(temp));
wait(200);
NrfRSSI = transportGetReceivingRSSI();
NrfRSSI2 = map(NrfRSSI, -85, -40, 0, 100);
if (NrfRSSI2 < 0) {
NrfRSSI2 = 0;
}
if (NrfRSSI2 > 100) {
NrfRSSI2 = 100;
}
send(msgRF52RssiReceiv.set(NrfRSSI2));
wait(200);
}Juhtumifailid stl-s -
Gerberi PCB-failid -
Kui teil on küsimusi selle arenduse kohta, teie Arduinose ja Mysensorite arenduste raskuste kohta, tulevad meie telegrammivestluses alati appi - .
Allikas: www.habr.com