Kuvassa Linux-ydin lähettää sinulle terveisiä GPIO:n kautta.
Tässä osassa tarinaa RISC-V RocketChipin siirtämisestä kiinalaiselle levylle Cyclone IV:llä, käytämme edelleen Linuxia ja opimme myös itse määrittämään IP Core -muistiohjaimen ja muokkaamaan hieman laitteen DTS-kuvausta. Tämä artikkeli on jatkoa , mutta toisin kuin melko laaja edellinen, se on melko lyhyt.
… Koska setup_smp kutsutaan vain, jos ytimessä on SMP-tuki, voit yrittää poistaa moniytimisen käytöstä. On epämiellyttävää, jos minun on otettava käyttöön myös atomituki muistimoduulissa (minusta tuntui, että välimuisti tekee tämän itsekseen), mutta yhden ytimen tapauksessa sen ei pitäisi häiritä meitä.
Ei vieläkään lähtenyt...
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Linux version 4.19.0-sifive-1+ (trosinenko@trosinenko-pc) (gcc version 8.3.0 (Buildroot 2019.02-07449-g4eddd28f99)) #1 Thu Jul 4 18:38:10 MSK 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] Initial ramdisk at: 0x(____ptrval____) (16777216 bytes)
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Normal [mem 0x00000000c0000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] software IO TLB: mapped [mem 0xbb1fc000-0xbf1fc000] (64MB)
[ 0.000000] Unable to find "cpu" devicetree entry
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055
[ 0.000000] Kernel command line: debug console=ttySIF0,125200 root=/dev/mmcblk0p2 loglevel=7 rootwait
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] BUG: Bad page state in process swapper pfn:80bf7
[ 0.000000] page:ffffffe03f029e08 count:0 mapcount:-65280 mapping:0000000000000000 index:0x1
[ 0.000000] flags: 0x0()
[ 0.000000] raw: 0000000000000000 0000000000000100 0000000000000200 0000000000000000
[ 0.000000] raw: 0000000000000001 0000000000000000 00000000ffff00ff
[ 0.000000] page dumped because: nonzero mapcount
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.19.0-sifive-1+ #1
[ 0.000000] Call Trace:
[ 0.000000] [<ffffffe00002cfde>] walk_stackframe+0x0/0xa0
[ 0.000000] [<ffffffe00002d1da>] show_stack+0x2a/0x34
[ 0.000000] [<ffffffe00063c898>] chachachllachachachTradeonachachach_inachachipachachachachllachachachTradeonachachachdevachachachypachachachllachachachTradeona+0x20/0x28
[ 0.000000] [<ffffffe00009499c>] bad_page+0xe4/0x102
[ 0.000000] [<ffffffe0000949f2>] free_pages_check_bad+0x38/0x7a
[ 0.000000] [<ffffffe000094bb0>] free_pcppages_bulk+0x106/0x36c
[ 0.000000] [<ffffffe0000957be>] free_unref_page_commit.isra.23+0x86/0x8e
[ 0.000000] [<ffffffe0000960bc>] free_unref_page+0x44/0x58
[ 0.000000] [<ffffffe0000960de>] __free_pages.part.28+0xe/0x22
[ 0.000000] [<ffffffe0000056da>] __free_pages_bootmem+0x86/0x90
[ 0.000000] [<ffffffe000007c46>] free_all_bootmem+0x156/0x1ba
[ 0.000000] [<ffffffe0000023f8>] mem_init+0x36/0x44
[ 0.000000] [<ffffffe0000007a0>] start_kernel+0x1aa/0x328
[ 0.000000] [<ffffffe000000058>] _sinittext+0x58/0x5c
[ 0.000000] Disabling lock debugging due to kernel taint
[ 0.000000] BUG: Bad page state in process swapper pfn:80bf9
[ 0.000000] page:ffffffe03f029e78 count:0 mapcount:-65280 mapping:0000000000000000 index:0x0
[ 0.000000] flags: 0x0()
[ 0.000000] raw: 0000000000000000 ffffffe03f020080 ffffffe03f020080 0000000000000000
[ 0.000000] raw: 0000000000000000 0000000000000000 00000000ffff00ff
[ 0.000000] page dumped because: nonzero mapcount
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Tainted: G B 4.19.0-sifive-1+ #1
[ 0.000000] Call Trace:
[ 0.000000] [<ffffffe00002cfde>] walk_stackframe+0x0/0xa0
[ 0.000000] [<ffffffe00002d1da>] show_stack+0x2a/0x34
[ 0.000000] [<ffffffe00063c898>] chachachllachachachTradeonachachach_inachachipachachachachllachachachTradeonachachachdevachachachypachachachllachachachTradeona+0x20/0x28
[ 0.000000] [<ffffffe00009499c>] bad_page+0xe4/0x102
[ 0.000000] [<ffffffe0000949f2>] free_pages_check_bad+0x38/0x7a
[ 0.000000] [<ffffffe0000955c6>] __free_pages_ok+0x3fe/0x430
[ 0.000000] [<ffffffe0000960ea>] __free_pages.part.28+0x1a/0x22
[ 0.000000] [<ffffffe0000056da>] __free_pages_bootmem+0x86/0x90
[ 0.000000] [<ffffffe000007c46>] free_all_bootmem+0x156/0x1ba
[ 0.000000] [<ffffffe0000023f8>] mem_init+0x36/0x44
[ 0.000000] [<ffffffe0000007a0>] start_kernel+0x1aa/0x328
[ 0.000000] [<ffffffe000000058>] _sinittext+0x58/0x5c
[ 0.000000] BUG: Bad page state in process swapper pfn:80bfa
[ 0.000000] page:ffffffe03f029eb0 count:0 mapcount:-65280 mapping:0000000000000000 index:0x0
[ 0.000000] flags: 0x0()
[ 0.000000] raw: 0000000000000000 ffffffe03f0200b8 ffffffe03f0200b8 0000000000000000
[ 0.000000] raw: 0000000000000000 0000000000000000 00000000ffff00ff
[ 0.000000] page dumped because: nonzero mapcount
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Tainted: G B 4.19.0-sifive-1+ #1
[ 0.000000] Call Trace:
[ 0.000000] [<ffffffe00002cfde>] walk_stackframe+0x0/0xa0
[ 0.000000] [<ffffffe00002d1da>] show_stack+0x2a/0x34
[ 0.000000] [<ffffffe00063c898>] chachachllachachachTradeonachachach_inachachipachachachachllachachachTradeonachachachdevachachachypachachachllachachachTradeona+0x20/0x28
[ 0.000000] [<ffffffe00009499c>] bad_page+0xe4/0x102
[ 0.000000] [<ffffffe0000949f2>] free_pages_check_bad+0x38/0x7a
[ 0.000000] [<ffffffe0000955c6>] __free_pages_ok+0x3fe/0x430
[ 0.000000] [<ffffffe0000960ea>] __free_pages.part.28+0x1a/0x22
[ 0.000000] [<ffffffe0000056da>] __free_pages_bootmem+0x86/0x90
[ 0.000000] [<ffffffe000007c46>] free_all_bootmem+0x156/0x1ba
[ 0.000000] [<ffffffe0000023f8>] mem_init+0x36/0x44
[ 0.000000] [<ffffffe0000007a0>] start_kernel+0x1aa/0x328
[ 0.000000] [<ffffffe000000058>] _sinittext+0x58/0x5c
[ 0.000000] BUG: Bad page state in process swapper pfn:80bfb
[ 0.000000] page:ffffffe03f029ee8 count:0 mapcount:-65280 mapping:0000000000000000 index:0x0
[ 0.000000] flags: 0x0()
[ 0.000000] raw: 0000000000000000 ffffffe03f0200f0 ffffffe03f0200f0 0000000000000000
[ 0.000000] raw: 0000000000000000 0000000000000000 00000000ffff00ff
[ 0.000000] page dumped because: nonzero mapcount
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Tainted: G B 4.19.0-sifive-1+ #1
[ 0.000000] Call Trace:
[ 0.000000] [<ffffffe00002cfde>] walk_stackframe+0x0/0xa0
[ 0.000000] [<ffffffe00002d1da>] show_stack+0x2a/0x34
[ 0.000000] [<ffffffe00063c898>] chachachllachachachTradeonachachach_inachachipachachachachllachachachTradeonachachachdevachachachypachachachllachachachTradeona+0x20/0x28
[ 0.000000] [<ffffffe00009499c>] bad_page+0xe4/0x102
[ 0.000000] [<ffffffe0000949f2>] free_pages_check_bad+0x38/0x7a
[ 0.000000] [<ffffffe0000955c6>] __free_pages_ok+0x3fe/0x430
[ 0.000000] [<ffffffe0000960ea>] __free_pages.part.28+0x1a/0x22
[ 0.000000] [<ffffffe0000056da>] __free_pages_bootmem+0x86/0x90
[ 0.000000] [<ffffffe000007c46>] free_all_bootmem+0x156/0x1ba
[ 0.000000] [<ffffffe0000023f8>] mem_init+0x36/0x44
[ 0.000000] [<ffffffe0000007a0>] start_kernel+0x1aa/0x328
[ 0.000000] [<ffffffe000000058>] _sinittext+0x58/0x5c
[ 0.000000] BUG: Bad page state in process swapper pfn:80bfc
[ 0.000000] page:ffffffe03f029f20 count:0 mapcount:-65280 mapping:0000000000000000 index:0x0
[ 0.000000] flags: 0x0()
[ 0.000000] raw: 0000000000000000 ffffffe03f020028 ffffffe03f020028 0000000000000000
[ 0.000000] raw: 0000000000000000 0000000000000000 00000000ffff00ff
...On mielenkiintoista, että kaiken virheenkorjauksen jälkeen päätin katsoa, miltä "viiteytimen" tulosteen pitäisi näyttää, hän sanoi. make qemu, ja näin samanlaisen virheen.
Valitettavasti seuraava taso (Linux-ydin) on monimutkaisempi: GDB, joka on yhdistetty JTAG:n kautta RocketChipiin, toimii ilmeisesti fyysisten osoitteiden kanssa riippumatta siitä, miten MMU on konfiguroitu, ja tällä hetkellä kiinnostava ydin on jo määrittänyt näytön osoitteita, joten se on helppo sanoa display/10i $pc se ei onnistu - näemme vain paljon unimp. Mutta jos olemme jo selvittäneet offsetin (näyttää siltä 0x80200000 -> 0xffffffe000000000), niin voit huijata:
1: x/10i $pc
=> 0xffffffe000002436 <setup_smp>: unimp
0xffffffe000002438 <setup_smp+2>: unimp
0xffffffe00000243a <setup_smp+4>: unimp
0xffffffe00000243c <setup_smp+6>: unimp
0xffffffe00000243e <setup_smp+8>: unimp
0xffffffe000002440 <setup_smp+10>: unimp
0xffffffe000002442 <setup_smp+12>: unimp
0xffffffe000002444 <setup_smp+14>: unimp
0xffffffe000002446 <setup_smp+16>: unimp
0xffffffe000002448 <setup_smp+18>: unimp
(gdb) undisplay 1
(gdb) display/10i ($pc - 0xffffffe000002436 + 0x80202436)
2: x/10i ($pc - 0xffffffe000002436 + 0x80202436)
0x80202436: addi sp,sp,-96
0x80202438: sd s0,80(sp)
0x8020243a: sd s1,72(sp)
0x8020243c: sd s2,64(sp)
0x8020243e: sd s3,56(sp)
0x80202440: sd s4,48(sp)
0x80202442: sd s5,40(sp)
0x80202444: sd s6,32(sp)
0x80202446: sd s7,24(sp)
0x80202448: sd s8,16(sp)Katkopisteet asetetaan samalla tavalla:
(gdb) p setup_smp
$1 = {<text variable, no debug info>} 0xffffffe000002436 <setup_smp>
(gdb) b *0x80202436
Breakpoint 1 at 0x80202436
(gdb) c
Continuing.
Program received signal SIGTRAP, Trace/breakpoint trap.
setup_smp () at /home/trosinenko/freedom-u-sdk/linux/arch/riscv/kernel/smpboot.c:58
58 while ((dn = of_find_node_by_type(dn, "cpu"))) {
(gdb) bt
#0 setup_smp () at /home/trosinenko/freedom-u-sdk/linux/arch/riscv/kernel/smpboot.c:58
#1 0xffffffe0000022a2 in setup_arch () at /home/trosinenko/freedom-u-sdk/linux/arch/riscv/kernel/setup.c:253
#2 0x0000000000000000 in ?? ()
Backtrace stopped: frame did not save the PCMutta sinun on poistettava ne manuaalisesti päästäksesi eteenpäin - GDB:lle tämä on jonkinlainen täysin käsittämätön ansa. Ai niin, jos satut sanomaan s tai n sen sijasta si, gdb yrittää lisätä implisiittisen keskeytyskohdan, jota ei ilmeisistä syistä voida asettaa, mutta GDB:tä ei voi estää. Mutta älä kiirehdi käynnistämään levyä uudelleen - havaintojeni mukaan riittää, että käynnistät vain gdb: n uudelleen (huomaa, että vanhat keskeytyskohdat eivät välttämättä katoa).
Itse asiassa sinun on käsiteltävä alkuperäistä ongelmaa: virheenkorjauksen sijoittamista printk funktioksi of_find_node_by_type, jota käyttää käynnistysprosessorin ytimen hakukoodi, osoittaa, että se näkee jonkinlaista roskaa laitetyyppien nimien sijaan. Esimerkiksi se ottaa jostain rivin "Serial port", vaikka tämä ei selvästikään ole dtb-kentässä device_type. Etsittyäni näitä tavuja ytimen kuvasta, löysin ne, katsoin offsetin ja tajusin ilmeisen: ytimen koko käynnistysparametreissa on selvästi aliarvioitu: sille on varattu 8 Mt, mutta se vie yli kymmenen. Varasin 16Mb, mutta outous ei loppunut. Tanssittuaan FDT:n lukemisen eri osoitteista (yleensä osoite siirretään ytimeen rekisterissä a1), päätin lopulta jäljittää, mutta mitä сейчас se on jäsennetty siellä. Onneksi sen sijaan, että kävelisit debuggerin kanssa (ja muistamme, että osoitteen käännöksessä on vivahteita, jotka on vielä ratkaistava tavalla tai toisella), voit yksinkertaisesti ja tunkeutua tiedostoon drivers/of/fdt.c eritellä #define pr_debug printk. Tuloksena oli:
debug-tulosteen lisääminen
diff --git a/arch/riscv/kernel/setup.c b/arch/riscv/kernel/setup.c
index 3db0d71d128b..fac47df9d1db 100644
--- a/arch/riscv/kernel/setup.c
+++ b/arch/riscv/kernel/setup.c
@@ -173,6 +173,7 @@ asmlinkage void __init setup_vm(void)
void __init parse_dtb(unsigned int hartid, void *dtb)
{
+ printk("HART = %u DTB = %lxn", hartid, dtb);
early_init_dt_scan(__va(dtb));
}
diff --git a/drivers/of/base.c b/drivers/of/base.c
index 74eaedd5b860..c019e4158e1d 100644
--- a/drivers/of/base.c
+++ b/drivers/of/base.c
@@ -940,10 +940,12 @@ struct device_node *of_find_node_by_type(struct device_node *from,
unsigned long flags;
raw_spin_lock_irqsave(&devtree_lock, flags);
- for_each_of_allnodes_from(from, np)
+ for_each_of_allnodes_from(from, np) {
+ printk("%lx %lx [%s] | [%s]n", from, np, np->type, type);
if (np->type && (of_node_cmp(np->type, type) == 0)
&& of_node_get(np))
break;
+ }
of_node_put(from);
raw_spin_unlock_irqrestore(&devtree_lock, flags);
return np;
diff --git a/drivers/of/fdt.c b/drivers/of/fdt.c
index 800ad252cf9c..2b45870ebada 100644
--- a/drivers/of/fdt.c
+++ b/drivers/of/fdt.c
@@ -31,6 +31,8 @@
#include "of_private.h"
+#define pr_debug printk
+
/*
* of_fdt_limit_memory - limit the number of regions in the /memory node
* @limit: maximum entries
@@ -1253,6 +1255,7 @@ bool __init early_init_dt_scan(void *params)
*/
void __init unflatten_device_tree(void)
{
+ printk("INITIAL: %lxn", initial_boot_params);
__unflatten_device_tree(initial_boot_params, NULL, &of_root,
early_init_dt_alloc_memory_arch, false);Tulostus laitteistolle
SIFIVE, INC.
5555555555555555555555555
5555 5555
5555 5555
5555 5555
5555 5555555555555555555555
5555 555555555555555555555555
5555 5555
5555 5555
5555 5555
5555555555555555555555555555 55555
55555 555555555 55555
55555 55555 55555
55555 5 55555
55555 55555
55555 55555
55555 55555
55555 55555
55555 55555
555555555
55555
5
SiFive RISC-V Core IP
{
#address-cells = <0x00000001>;
#size-cells = <0x00000001>;
compatible = "freechips,rocketchip-unknown-dev";
model = "freechips,rocketchip-unknown";
chosen {
linux,initrd-start = <0x82000000>;
riscv,kernel-end = <0x81200000>;
riscv,kernel-start = <0x80200000>;
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
bootargs = <0x64656275 0x6720636f 0x6e736f6c 0x653d7474 0x79534946 0x302c3132 0x35323030 0x20726f6f 0x743d2f64 0x65762f6d 0x6d63626c 0x6b307032 0x206c6f67 0x6c657665 0x6c3d3720 0x726f6f74 0x77616974>;
}
firmware {
sifive,uboot = "YYYY-MM-DD";
}
aliases {
serial0 = <0x2f736f63 0x2f736572 0x69616c40 0x36343030 0x30303030>;
}
cpus {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
cpu@0 {
device_type = "cpu";
clock-frequency = <0x00000000>;
compatible = "sifive,rocket0", "riscv";
d-cache-block-size = <0x00000010>;
d-cache-sets = <0x00000040>;
d-cache-size = <0x00001000>;
d-tlb-sets = <0x00000001>;
d-tlb-size = <0x00000020>;
i-cache-block-size = <0x00000010>;
i-cache-sets = <0x00000040>;
i-cache-size = <0x00001000>;
i-tlb-sets = <0x00000001>;
i-tlb-size = <0x00000020>;
mmu-type = "riscv,sv39";
next-level-cache = <0x00000001>;
reg = <0x00000000>;
riscv,isa = "rv64imafdc";
status = "okay";
timebase-frequency = <0x000f4240>;
tlb-split;
interrupt-controller {
#interrupt-cells = <0x00000001>;
compatible = "riscv,cpu-intc";
interrupt-controller;
phandle = <0x00000002>;
}
}
}
ram@80000000 {
device_type = "memory";
reg = <0x80000000 0x40000000>;
reg-names = "mem";
phandle = <0x00000001>;
}
soc {
#address-cells = <0x00000001>;
#size-cells = <0x00000001>;
compatible = "freechips,rocketchip-unknown-soc", "simple-bus";
ranges;
clint@2000000 {
compatible = "riscv,clint0";
interrupts-extended = <0x00000002 0x00000003 0x00000002 0x00000007>;
reg = <0x02000000 0x00010000>;
reg-names = "control";
}
debug-controller@0 {
compatible = "sifive,debug-013", "riscv,debug-013";
interrupts-extended = <0x00000002 0x0000ffff>;
reg = <0x00000000 0x00001000>;
reg-names = "control";
}
gpio@64002000 {
#gpio-cells = <0x00000002>;
#interrupt-cells = <0x00000002>;
compatible = "sifive,gpio0";
gpio-controller;
interrupt-controller;
interrupt-parent = <0x00000003>;
interrupts = <0x00000003 0x00000004 0x00000005 0x00000006 0x00000007 0x00000008>;
reg = <0x64002000 0x00001000>;
reg-names = "control";
}
interrupt-controller@c000000 {
#interrupt-cells = <0x00000001>;
compatible = "riscv,plic0";
interrupt-controller;
interrupts-extended = <0x00000002 0x0000000b 0x00000002 0x00000009>;
reg = <0x0c000000 0x04000000>;
reg-names = "control";
riscv,max-priority = <0x00000007>;
riscv,ndev = <0x00000008>;
phandle = <0x00000003>;
}
rom@10000 {
compatible = "sifive,maskrom0";
reg = <0x00010000 0x00002000>;
reg-names = "mem";
}
serial@64000000 {
compatible = "sifive,uart0";
interrupt-parent = <0x00000003>;
interrupts = <0x00000002>;
reg = <0x64000000 0x00001000>;
reg-names = "control";
}
spi@64001000 {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
compatible = "sifive,spi0";
interrupt-parent = <0x00000003>;
interrupts = <0x00000001>;
reg = <0x64001000 0x00001000>;
reg-names = "control";
mmc@0 {
compatible = "mmc-spi-slot";
disable-wp;
reg = <0x00000000>;
spi-max-frequency = <0x01312d00>;
voltage-ranges = <0x00000ce4 0x00000ce4>;
}
}
tlclk {
#clock-cells = <0x00000000>;
clock-frequency = <0x017d7840>;
clock-output-names = "tlclk";
compatible = "fixed-clock";
}
}
}
[ 0.000000] HART = 0 DTB = 81200000
[ 0.000000] search "chosen", depth: 0, uname:
[ 0.000000] search "chosen", depth: 1, uname: chosen
[ 0.000000] Looking for initrd properties...
[ 0.000000] Command line is: debug console=ttySIF0,125200 root=/dev/mmcblk0p2 loglevel=7 rootwait
[ 0.000000] dt_root_size_cells = 1
[ 0.000000] dt_root_addr_cells = 1
[ 0.000000] memory scan node ram@80000000, reg size 8,
[ 0.000000] - 80000000 , 40000000
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Linux version 4.19.0-sifive-1+ (trosinenko@trosinenko-pc) (gcc version 8.3.0 (Buildroot 2019.02-07449-g4eddd28f99)) #1 SMP Sat Jul 6 12:14:41 MSK 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Normal [mem 0x00000000c0000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] INITIAL: ffffffe001000000
[ 0.000000] -> unflatten_device_tree()
[ 0.000000] Unflattening device tree:
[ 0.000000] magic: d00dfeed
[ 0.000000] size: 00001000
[ 0.000000] version: 00000011
[ 0.000000] size is 13512, allocating...
[ 0.000000] unflattening (____ptrval____)...
[ 0.000000] fixed up name for ->
[ 0.000000] fixed up name for chosen -> chosen
[ 0.000000] fixed up name for firmware -> firmware
[ 0.000000] fixed up name for aliases -> aliases
[ 0.000000] fixed up name for cpus -> cpus
[ 0.000000] fixed up name for cpu@0 -> cpu
[ 0.000000] fixed up name for interrupt-controller -> interrupt-controller
[ 0.000000] fixed up name for ram@80000000 -> ram
[ 0.000000] fixed up name for soc -> soc
[ 0.000000] fixed up name for clint@2000000 -> clint
[ 0.000000] fixed up name for debug-controller@0 -> debug-controller
[ 0.000000] fixed up name for gpio@64002000 -> gpio
[ 0.000000] fixed up name for interrupt-controller@c000000 -> interrupt-controller
[ 0.000000] fixed up name for rom@10000 -> rom
[ 0.000000] fixed up name for serial@64000000 -> serial
[ 0.000000] fixed up name for spi@64001000 -> spi
[ 0.000000] fixed up name for mmc@0 -> mmc
[ 0.000000] fixed up name for tlclk -> tlclk
[ 0.000000] <- unflatten_device_tree()
[ 0.000000] software IO TLB: mapped [mem 0xbb1fc000-0xbf1fc000] (64MB)
[ 0.000000] 0 ffffffe03effcab0 [attach() failed for %s with error %d
[ 0.000000] ] | [cpu]
[ 0.000000] 0 ffffffe03eff0020 [(null)] | [cpu]Lähtö QEMU:lle
SIFIVE, INC.
5555555555555555555555555
5555 5555
5555 5555
5555 5555
5555 5555555555555555555555
5555 555555555555555555555555
5555 5555
5555 5555
5555 5555
5555555555555555555555555555 55555
55555 555555555 55555
55555 55555 55555
55555 5 55555
55555 55555
55555 55555
55555 55555
55555 55555
55555 55555
555555555
55555
5
SiFive RISC-V Core IP
{
#address-cells = <0x00000002>;
#size-cells = <0x00000002>;
compatible = "riscv-virtio";
model = "riscv-virtio,qemu";
chosen {
linux,initrd-start = <0x00000000 0x88000000>;
linux,initrd-end = <0x00000000 0x88442b86>;
riscv,kernel-start = <0x00000000 0x80200000>;
riscv,kernel-end = <0x00000000 0x80c482ac>;
bootargs = "";
stdout-path = <0x2f756172 0x74403130 0x30303030>;
}
uart@10000000 {
interrupts = <0x0000000a>;
interrupt-parent = <0x00000002>;
clock-frequency = <0x00384000>;
reg = <0x00000000 0x10000000 0x00000000 0x00000100>;
compatible = "ns16550a";
}
test@100000 {
reg = <0x00000000 0x00100000 0x00000000 0x00001000>;
compatible = "sifive,test0";
}
virtio_mmio@10008000 {
interrupts = <0x00000008>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10008000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10007000 {
interrupts = <0x00000007>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10007000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10006000 {
interrupts = <0x00000006>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10006000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10005000 {
interrupts = <0x00000005>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10005000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10004000 {
interrupts = <0x00000004>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10004000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10003000 {
interrupts = <0x00000003>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10003000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10002000 {
interrupts = <0x00000002>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10002000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10001000 {
interrupts = <0x00000001>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10001000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
cpus {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
timebase-frequency = <0x00989680>;
cpu@0 {
device_type = "cpu";
reg = <0x00000000>;
status = "okay";
compatible = "riscv";
riscv,isa = "rv64imafdcsu";
mmu-type = "riscv,sv48";
clock-frequency = <0x3b9aca00>;
interrupt-controller {
#interrupt-cells = <0x00000001>;
interrupt-controller;
compatible = "riscv,cpu-intc";
linux,phandle = <0x00000001>;
phandle = <0x00000001>;
}
}
}
memory@80000000 {
device_type = "memory";
reg = <0x00000000 0x80000000 0x00000000 0x40000000>;
}
soc {
#address-cells = <0x00000002>;
#size-cells = <0x00000002>;
compatible = "simple-bus";
ranges;
pci@30000000 {
interrupt-map-mask = <0x00001800 0x00000000 0x00000000 0x00000007>;
interrupt-map = <0x00000000 0x00000000 0x00000000 0x00000001 0x00000002 0x00000020 0x00000000 0x00000000 0x00000000 0x00000002 0x00000002 0x00000021 0x00000000 0x00000000 0x00000000 0x00000003 0x00000002 0x00000022 0x00000000 0x00000000 0x00000000 0x00000004 0x00000002 0x00000023 0x00000800 0x00000000 0x00000000 0x00000001 0x00000002 0x00000021 0x00000800 0x00000000 0x00000000 0x00000002 0x00000002 0x00000022 0x00000800 0x00000000 0x00000000 0x00000003 0x00000002 0x00000023 0x00000800 0x00000000 0x00000000 0x00000004 0x00000002 0x00000020 0x00001000 0x00000000 0x00000000 0x00000001 0x00000002 0x00000022 0x00001000 0x00000000 0x00000000 0x00000002 0x00000002 0x00000023 0x00001000 0x00000000 0x00000000 0x00000003 0x00000002 0x00000020 0x00001000 0x00000000 0x00000000 0x00000004 0x00000002 0x00000021 0x00001800 0x00000000 0x00000000 0x00000001 0x00000002 0x00000023 0x00001800 0x00000000 0x00000000 0x00000002 0x00000002 0x00000020 0x00001800 0x00000000 0x00000000 0x00000003 0x00000002 0x00000021 0x00001800 0x00000000 0x00000000 0x00000004 0x00000002 0x00000022>;
ranges = <0x01000000 0x00000000 0x00000000 0x00000000 0x03000000 0x00000000 0x00010000 0x02000000 0x00000000 0x40000000 0x00000000 0x40000000 0x00000000 0x40000000>;
reg = <0x00000000 0x30000000 0x00000000 0x10000000>;
dma-coherent;
bus-range = <0x00000000 0x000002ff>;
linux,pci-domain = <0x00000000>;
device_type = "pci";
compatible = "pci-host-ecam-generic";
#size-cells = <0x00000002>;
#interrupt-cells = <0x00000001>;
#address-cells = <0x00000003>;
}
interrupt-controller@c000000 {
linux,phandle = <0x00000002>;
phandle = <0x00000002>;
riscv,ndev = <0x00000035>;
riscv,max-priority = <0x00000007>;
reg-names = "control";
reg = <0x00000000 0x0c000000 0x00000000 0x04000000>;
interrupts-extended = <0x00000001 0x0000000b 0x00000001 0x00000009>;
interrupt-controller;
compatible = "riscv,plic0";
#interrupt-cells = <0x00000001>;
#address-cells = <0x00000000>;
}
clint@2000000 {
interrupts-extended = <0x00000001 0x00000003 0x00000001 0x00000007>;
reg = <0x00000000 0x02000000 0x00000000 0x00010000>;
compatible = "riscv,clint0";
}
}
}
[ 0.000000] HART = 0 DTB = 80e00000
[ 0.000000] search "chosen", depth: 0, uname:
[ 0.000000] search "chosen", depth: 1, uname: chosen
[ 0.000000] Looking for initrd properties...
[ 0.000000] initrd_start=0x88000000 initrd_end=0x88442b86
[ 0.000000] Command line is: earlyprintk
[ 0.000000] dt_root_size_cells = 2
[ 0.000000] dt_root_addr_cells = 2
[ 0.000000] memory scan node memory@80000000, reg size 16,
[ 0.000000] - 80000000 , 40000000
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Linux version 4.19.0-sifive-1+ (trosinenko@trosinenko-pc) (gcc version 8.3.0 (Buildroot 2019.02-07449-g4eddd28f99)) #1 SMP Sat Jul 6 12:14:41 MSK 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] Initial ramdisk at: 0x(____ptrval____) (4467590 bytes)
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Normal [mem 0x00000000c0000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] INITIAL: ffffffe000c00000
[ 0.000000] -> unflatten_device_tree()
[ 0.000000] Unflattening device tree:
[ 0.000000] magic: d00dfeed
[ 0.000000] size: 00000d56
[ 0.000000] version: 00000011
[ 0.000000] size is 14192, allocating...
[ 0.000000] unflattening (____ptrval____)...
[ 0.000000] fixed up name for ->
[ 0.000000] fixed up name for chosen -> chosen
[ 0.000000] fixed up name for uart@10000000 -> uart
[ 0.000000] fixed up name for test@100000 -> test
[ 0.000000] fixed up name for virtio_mmio@10008000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10007000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10006000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10005000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10004000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10003000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10002000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10001000 -> virtio_mmio
[ 0.000000] fixed up name for cpus -> cpus
[ 0.000000] fixed up name for cpu@0 -> cpu
[ 0.000000] fixed up name for interrupt-controller -> interrupt-controller
[ 0.000000] fixed up name for memory@80000000 -> memory
[ 0.000000] fixed up name for soc -> soc
[ 0.000000] fixed up name for pci@30000000 -> pci
[ 0.000000] fixed up name for interrupt-controller@c000000 -> interrupt-controller
[ 0.000000] fixed up name for clint@2000000 -> clint
[ 0.000000] <- unflatten_device_tree()
[ 0.000000] software IO TLB: mapped [mem 0xbb1fc000-0xbf1fc000] (64MB)
[ 0.000000] 0 ffffffe03effc808 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effca78 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effcd98 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd068 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd230 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd4b8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd740 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd9c8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effdc50 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effded8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe160 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe3e8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe670 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe888 [cpu] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03effec00 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03effeee8 [memory] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff0b0 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff320 [pci] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff858 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efffd58 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effc808 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effca78 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effcd98 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd068 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd230 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd4b8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd740 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd9c8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effdc50 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effded8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe160 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe3e8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe670 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe888 [cpu] | [cpu]
[ 0.000000] elf_hwcap is 0x112d
[ 0.000000] percpu: Embedded 17 pages/cpu @(____ptrval____) s29400 r8192 d32040 u69632
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055
[ 0.000000] Kernel command line: earlyprintk
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 949716K/1046528K available (6565K kernel code, 342K rwdata, 2564K rodata, 208K init, 832K bss, 96812K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[ 0.000000] plic: mapped 53 interrupts to 2 (out of 2) handlers.
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x24e6a1710, max_idle_ns: 440795202120 ns
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] bootconsole [early0] disabled
[ 0.000000] HART = 0 DTB = 80e00000
[ 0.000000] search "chosen", depth: 0, uname:
[ 0.000000] search "chosen", depth: 1, uname: chosen
[ 0.000000] Looking for initrd properties...
[ 0.000000] initrd_start=0x88000000 initrd_end=0x88442b86
[ 0.000000] Command line is: earlyprintk
[ 0.000000] dt_root_size_cells = 2
[ 0.000000] dt_root_addr_cells = 2
[ 0.000000] memory scan node memory@80000000, reg size 16,
[ 0.000000] - 80000000 , 40000000
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Linux version 4.19.0-sifive-1+ (trosinenko@trosinenko-pc) (gcc version 8.3.0 (Buildroot 2019.02-07449-g4eddd28f99)) #1 SMP Sat Jul 6 12:14:41 MSK 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] Initial ramdisk at: 0x(____ptrval____) (4467590 bytes)
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Normal [mem 0x00000000c0000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] INITIAL: ffffffe000c00000
[ 0.000000] -> unflatten_device_tree()
[ 0.000000] Unflattening device tree:
[ 0.000000] magic: d00dfeed
[ 0.000000] size: 00000d56
[ 0.000000] version: 00000011
[ 0.000000] size is 14192, allocating...
[ 0.000000] unflattening (____ptrval____)...
[ 0.000000] fixed up name for ->
[ 0.000000] fixed up name for chosen -> chosen
[ 0.000000] fixed up name for uart@10000000 -> uart
[ 0.000000] fixed up name for test@100000 -> test
[ 0.000000] fixed up name for virtio_mmio@10008000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10007000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10006000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10005000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10004000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10003000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10002000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10001000 -> virtio_mmio
[ 0.000000] fixed up name for cpus -> cpus
[ 0.000000] fixed up name for cpu@0 -> cpu
[ 0.000000] fixed up name for interrupt-controller -> interrupt-controller
[ 0.000000] fixed up name for memory@80000000 -> memory
[ 0.000000] fixed up name for soc -> soc
[ 0.000000] fixed up name for pci@30000000 -> pci
[ 0.000000] fixed up name for interrupt-controller@c000000 -> interrupt-controller
[ 0.000000] fixed up name for clint@2000000 -> clint
[ 0.000000] <- unflatten_device_tree()
[ 0.000000] software IO TLB: mapped [mem 0xbb1fc000-0xbf1fc000] (64MB)
[ 0.000000] 0 ffffffe03effc808 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effca78 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effcd98 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd068 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd230 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd4b8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd740 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd9c8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effdc50 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effded8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe160 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe3e8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe670 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe888 [cpu] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03effec00 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03effeee8 [memory] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff0b0 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff320 [pci] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff858 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efffd58 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effc808 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effca78 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effcd98 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd068 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd230 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd4b8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd740 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd9c8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effdc50 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effded8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe160 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe3e8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe670 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe888 [cpu] | [cpu]
[ 0.000000] elf_hwcap is 0x112d
[ 0.000000] percpu: Embedded 17 pages/cpu @(____ptrval____) s29400 r8192 d32040 u69632
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055
[ 0.000000] Kernel command line: earlyprintk
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 949716K/1046528K available (6565K kernel code, 342K rwdata, 2564K rodata, 208K init, 832K bss, 96812K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[ 0.000000] plic: mapped 53 interrupts to 2 (out of 2) handlers.
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x24e6a1710, max_idle_ns: 440795202120 ns
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] bootconsole [early0] disabled
[ 0.000000] Calibrating delay loop (skipped), value calculated using timer frequency.. 20.00 BogoMIPS (lpj=100000)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.000000] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.020000] rcu: Hierarchical SRCU implementation.
[ 0.020000] smp: Bringing up secondary CPUs ...
[ 0.020000] smp: Brought up 1 node, 1 CPU
[ 0.050000] devtmpfs: initialized
[ 0.050000] 0 ffffffe03effc808 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effca78 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effcd98 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effd068 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effd230 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effd4b8 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effd740 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effd9c8 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effdc50 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effded8 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effe160 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effe3e8 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effe670 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effe888 [cpu] | [cpu]
[ 0.050000] random: get_random_u32 called from bucket_table_alloc+0x76/0x17a with crng_init=0
[ 0.050000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.050000] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.060000] NET: Registered protocol family 16
[ 0.090000] vgaarb: loaded
[ 0.090000] SCSI subsystem initialized
[ 0.090000] usbcore: registered new interface driver usbfs
[ 0.090000] usbcore: registered new interface driver hub
[ 0.090000] usbcore: registered new device driver usb
[ 0.090000] pps_core: LinuxPPS API ver. 1 registered
[ 0.090000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 0.090000] PTP clock support registered
[ 0.100000] Advanced Linux Sound Architecture Driver Initialized.
[ 0.100000] clocksource: Switched to clocksource riscv_clocksource
[ 0.110000] NET: Registered protocol family 2
[ 0.110000] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes)
[ 0.110000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.110000] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 0.110000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.110000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.110000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.110000] NET: Registered protocol family 1
[ 0.120000] Unpacking initramfs...
[ 0.590000] workingset: timestamp_bits=62 max_order=18 bucket_order=0
[ 0.620000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.620000] io scheduler noop registered
[ 0.620000] io scheduler deadline registered
[ 0.620000] io scheduler cfq registered (default)
[ 0.620000] io scheduler mq-deadline registered
[ 0.620000] io scheduler kyber registered
[ 0.620000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 0.690000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.690000] 10000000.uart: ttyS0 at MMIO 0x10000000 (irq = 10, base_baud = 230400) is a 16550A
[ 0.720000] console [ttyS0] enabled
[ 0.720000] [drm] radeon kernel modesetting enabled.
[ 0.720000] [drm] amdgpu kernel modesetting enabled.
[ 0.730000] loop: module loaded
[ 0.730000] libphy: Fixed MDIO Bus: probed
[ 0.740000] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 0.740000] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 0.740000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.740000] ehci-pci: EHCI PCI platform driver
[ 0.740000] ehci-platform: EHCI generic platform driver
[ 0.740000] mousedev: PS/2 mouse device common for all mice
[ 0.740000] usbcore: registered new interface driver usbhid
[ 0.740000] usbhid: USB HID core driver
[ 0.740000] usbcore: registered new interface driver snd-usb-audio
[ 0.740000] NET: Registered protocol family 10
[ 0.750000] Segment Routing with IPv6
[ 0.750000] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 0.750000] NET: Registered protocol family 17
[ 0.750000] Key type dns_resolver registered
[ 0.760000] ALSA device list:
[ 0.760000] No soundcards found.
[ 0.770000] Freeing unused kernel memory: 208K
[ 0.770000] This architecture does not have kernel memory protection.
[ 0.770000] Run /init as init process("Aikaleimattuja" rivejä tuottaa ydin, niiden eteen BBL tuottaa puun) Toisaalta FDT luetaan onnistuneesti, toisaalta jonkinlaista hölynpölyä saadaan jäsennetyssä " esine” puu.
Vianetsintäprosessin aikana ymmärsin, että BBL ei voinut lukea "kaksoisosoitetta", ei siksi, että kokoonpanossa olisi virhe, vaan yksinkertaisesti siksi, että juurisolmulla oli #address-cells = <1>; #size-cells = <1>;.
Laajentuessani virheenkorjaustulosta huomasin, että se viittaa type и name "pahoinpidelty" ja melko oudolla tavalla: heidän ensimmäinen tavunsa (alkaen nollasta) nollattiin, jotenkin 0xabcdef -> 0xab00ef. Jouduin käyttämään tuttua taktiikkaa: kun tiedän osoitteet, joissa vaurioitunut muisti sijaitsee, lisää se toimintoon printk tulosta nämä tiedot. No itse haasteet printk hajottaa ne sinne, missä niitä on vähän. Valitettavasti se ei ole tullut paljon selvemmäksi. Sitten aloin neuvottelemaan purettuja objdump versio, aseta keskeytyskohdat manuaalisesti ja käy läpi koodin ongelmallinen osa vaihe vaiheelta. Ja sitten havaittiin mystinen ja epämiellyttävä asia: jos asetan välittömästi katkeamispisteen jonnekin suhteellisen kaukana tunnetusta hyvästä tilasta, niin siinä pysähtyessäni näen jo vaurioituneen muistin. Mutta jos yrität hiljaa hiipiä hänen luokseen askel askeleelta, bugi onnistuu piiloutumaan! Se haisee rikkinäiseltä muistiohjaimelta ja välimuistilta, joka piilottaa virheen, jos pyydät jatkuvasti vaadittua arvoa. Mitä jos…
Muistin vaihto
Tarttuessani mahdollisuuteen ratkaista ongelma, joka ei ollut minun puolellani, oletin, että ehkä olin juuri saanut rikkinäisen muistitikun. Sitten muistin, että kymmenen vuotta vanha netbook ei ole vain kannettava tietokone, vaan myös arvokas DDR2 SO-DIMM -lähde. Bonuksena voit laittaa siihen levyltä poistettua muistia ja saada Memtestin roikkumaan melkein välittömästi (Linux muuten ladattu melkein graafiseen kuoreen. Mutta on parempi olla toistamatta tätä kokeilua, jos arvostat asennettujen levyjen tietoja...). Toisaalta voimme olettaa, että muisti ei yksinkertaisesti sopinut tälle tietylle netbookille. Toisaalta hän pystyi käynnistymään! Oli toivoa, että muisti oli vain "rikki", eikä ongelma ollut kääreessäni.
Tämä tarkoittaa, että sinun on yritettävä käynnistää tilapäisesti netbook-muistilla. Valitettavasti Quartus 18 ei osaa päivittää tätä IP-ydintä niin, että sitä voidaan muokata. Tämä tarkoittaa, että on vihdoin tullut aika oppia luomaan uusia ilmentymiä. Kaikki osoittautui melko yksinkertaiseksi: etsimme IP-katalogista kohtaa DDR2 SDRAM Controller ALTMEMPHY Intel FPGA IP:llä ja saamme lohkon samalla käyttöliittymällä kuin ennen. Ainoa ongelma on oikeiden muistiasetusten asettaminen.
Muistimoduulin parametrien saaminen
Moduulin konfigurointiin on suhteellisen ilmeinen tapa: lue parametrit SPD:stä. Todellakin, jos tavallinen tietokone lukee SPD-tietoja ja konfiguroi ohjaimen sen perusteella, vähennetään nämä tiedot olemassa olevasta netbookista ja syötetään taulukkoon.
Tämä tehdään Ubuntussa : sinun on asennettava paketti i2c-tools, lataa moduuleja eeprom и i2c-i801 (En ole kuitenkaan varma, toimiiko toinen kuljettaja kaikkialla), juokse sitten decode-dimms:
Dekoodaa-himmentää lähtö
# decode-dimms version 6231 (2014-02-20 10:54:34 +0100)
Memory Serial Presence Detect Decoder
By Philip Edelbrock, Christian Zuckschwerdt, Burkart Lingner,
Jean Delvare, Trent Piepho and others
Decoding EEPROM: /sys/bus/i2c/drivers/eeprom/0-0050
Guessing DIMM is in bank 1
---=== SPD EEPROM Information ===---
EEPROM Checksum of bytes 0-62 OK (0x00)
SPD Revision Invalid
Fundamental Memory type Unknown (0x00)
---=== Manufacturing Information ===---
Manufacturer Undefined
Part Number Undefined
Decoding EEPROM: /sys/bus/i2c/drivers/eeprom/4-0050
Guessing DIMM is in bank 1
---=== SPD EEPROM Information ===---
EEPROM Checksum of bytes 0-62 OK (0x00)
SPD Revision Invalid
Fundamental Memory type Unknown (0x00)
---=== Manufacturing Information ===---
Manufacturer Undefined
Part Number Undefined
Decoding EEPROM: /sys/bus/i2c/drivers/eeprom/6-0050
Guessing DIMM is in bank 1
---=== SPD EEPROM Information ===---
EEPROM Checksum of bytes 0-62 OK (0x76)
# of bytes written to SDRAM EEPROM 128
Total number of bytes in EEPROM 256
Fundamental Memory type DDR2 SDRAM
SPD Revision 1.2
---=== Memory Characteristics ===---
Maximum module speed 800 MHz (PC2-6400)
Size 1024 MB
Banks x Rows x Columns x Bits 8 x 13 x 10 x 64
Ranks 2
SDRAM Device Width 16 bits
Module Height 30.0 mm
Module Type SO-DIMM (67.6 mm)
DRAM Package Planar
Voltage Interface Level SSTL 1.8V
Module Configuration Type No Parity
Refresh Rate Reduced (7.8 us) - Self Refresh
Supported Burst Lengths 4, 8
tCL-tRCD-tRP-tRAS 6-6-6-18
Supported CAS Latencies (tCL) 6T, 5T, 4T
Minimum Cycle Time 2.50 ns at CAS 6 (tCK min)
3.00 ns at CAS 5
3.75 ns at CAS 4
Maximum Access Time 0.40 ns at CAS 6 (tAC)
0.45 ns at CAS 5
0.50 ns at CAS 4
Maximum Cycle Time (tCK max) 8.00 ns
---=== Timing Parameters ===---
Address/Command Setup Time Before Clock (tIS) 0.17 ns
Address/Command Hold Time After Clock (tIH) 0.25 ns
Data Input Setup Time Before Strobe (tDS) 0.05 ns
Data Input Hold Time After Strobe (tDH) 0.12 ns
Minimum Row Precharge Delay (tRP) 15.00 ns
Minimum Row Active to Row Active Delay (tRRD) 10.00 ns
Minimum RAS# to CAS# Delay (tRCD) 15.00 ns
Minimum RAS# Pulse Width (tRAS) 45.00 ns
Write Recovery Time (tWR) 15.00 ns
Minimum Write to Read CMD Delay (tWTR) 7.50 ns
Minimum Read to Pre-charge CMD Delay (tRTP) 7.50 ns
Minimum Active to Auto-refresh Delay (tRC) 60.00 ns
Minimum Recovery Delay (tRFC) 127.50 ns
Maximum DQS to DQ Skew (tDQSQ) 0.20 ns
Maximum Read Data Hold Skew (tQHS) 0.30 ns
---=== Manufacturing Information ===---
Manufacturer Samsung
Manufacturing Location Code 0x02
Part Number M4 70T2864QZ3-CF7
Revision Code 0x3351
Manufacturing Date 2009-W34
Assembly Serial Number 0x79C64E9A
Number of SDRAM DIMMs detected and decoded: 3Ongelmana on, että joitain ajoituksia ei ole ilmoitettu tässä, joten lähdetään toiselle polulle.
Mitä moduuleihimme on kirjoitettu:
Tässä tapauksessa itse muistisirujen merkintä on mielenkiintoisempi: K4T1G164QQ-HCF7. Kirjoittamalla tämän rivin Googleen saamme useita kymmeniä sivuja sisältävän tietolomakkeen, jossa on kaikki tarvittavat parametrit, jotka voidaan sisällyttää siististi IP Core -ominaisuuksiin. Kiinnitä vain huomiota mittayksiköihin: jossain ns, jossain - ps, ja joskus jopa jakaa tCK. En opeta sinulle, mihin kiinnittää huomiota - määritin monia asioita itse satunnaisesti (en voi taata, että et voi "polttaa" muistia tai FPGA:ta tällä tavalla). Kiinnitän vain huomiosi tähän: en saanut säädintä toimimaan kovin pitkään, ja viimeinen askel oli oivallus, että minun piti tarkistaa kaikkien muistiliitäntöjen leveys luodun Verilog-koodin suhteen. : loppujen lopuksi, kun sisään MemIfBundle ilmoitettu val mem_ba = IO(Output(UInt(2.W))), ja pankkeja on 8 (eli 3 bitin leveä osoite), niin meillä on vain ilmassa roikkuvan muistiohjaimen lähtö - ongelma, mutta ei kriittinen, joten kaikki syntetisoidaan, mutta ei toimi.
Ehkä kaikki toimisi vanhan moduulin kanssa, jos ohjain päivitettäisiin, mutta toistaiseksi olen liian laiska käsittelemään mahdollisia kelluvia bugeja: minulla on tarpeeksi omaani.
Siis muuton jälkeen timebase-frequency DTS:ssä tietystä CPU-tasosta solmutasolle cpus (ytimen aivan ymmärrettävän pyynnön mukaan) saamme:
Piilotettu teksti
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Linux version 4.19.0-sifive-1+ (trosinenko@trosinenko-pc) (gcc version 8.3.0 (Buildroot 2019.02-07449-g4eddd28f99)) #1 SMP Tue Jul 9 22:42:36 MSK 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] Initial ramdisk at: 0x(____ptrval____) (16777216 bytes)
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Normal [mem 0x00000000c0000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] software IO TLB: mapped [mem 0xbb1fc000-0xbf1fc000] (64MB)
[ 0.000000] elf_hwcap is 0x112d
[ 0.000000] percpu: Embedded 17 pages/cpu @(____ptrval____) s29400 r8192 d32040 u69632
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055
[ 0.000000] Kernel command line: debug console=ttySIF0,125200 root=/dev/mmcblk0p2 loglevel=7 rootwait
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 937696K/1046528K available (6565K kernel code, 343K rwdata, 2564K rodata, 208K init, 832K bss, 108832K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[ 0.000000] plic: mapped 8 interrupts to 1 (out of 2) handlers.
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
[ 0.020000] pid_max: default: 32768 minimum: 301
[ 0.030000] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.040000] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.140000] rcu: Hierarchical SRCU implementation.
[ 0.190000] smp: Bringing up secondary CPUs ...
[ 0.190000] smp: Brought up 1 node, 1 CPU
[ 0.220000] devtmpfs: initialized
[ 0.300000] random: get_random_u32 called from bucket_table_alloc+0x76/0x17a with crng_init=0
[ 0.330000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.340000] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.380000] NET: Registered protocol family 16
[ 1.850000] vgaarb: loaded
[ 1.870000] SCSI subsystem initialized
[ 1.900000] usbcore: registered new interface driver usbfs
[ 1.910000] usbcore: registered new interface driver hub
[ 1.920000] usbcore: registered new device driver usb
[ 1.930000] pps_core: LinuxPPS API ver. 1 registered
[ 1.940000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 1.950000] PTP clock support registered
[ 1.970000] Advanced Linux Sound Architecture Driver Initialized.
[ 2.010000] clocksource: Switched to clocksource riscv_clocksource
[ 2.600000] NET: Registered protocol family 2
[ 2.640000] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes)
[ 2.650000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 2.670000] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 2.700000] TCP: Hash tables configured (established 8192 bind 8192)
[ 2.720000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 2.730000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 2.750000] NET: Registered protocol family 1
[ 2.770000] Unpacking initramfs...
[ 23.980000] Initramfs unpacking failed: junk in compressed archive
[ 24.030000] workingset: timestamp_bits=62 max_order=18 bucket_order=0
[ 25.020000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 25.030000] io scheduler noop registered
[ 25.040000] io scheduler deadline registered
[ 25.050000] io scheduler cfq registered (default)
[ 25.060000] io scheduler mq-deadline registered
[ 25.060000] io scheduler kyber registered
[ 25.120000] sifive_gpio 64002000.gpio: SiFive GPIO chip registered 6 GPIOs
[ 25.150000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 28.870000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 28.940000] sifive-serial 64000000.serial: unable to find controller clock
[ 28.950000] sifive-serial: probe of 64000000.serial failed with error -2
[ 28.980000] [drm] radeon kernel modesetting enabled.
[ 28.990000] [drm] amdgpu kernel modesetting enabled.
[ 29.500000] loop: module loaded
[ 29.610000] sifive_spi 64001000.spi: Unable to find bus clock
[ 29.620000] sifive_spi: probe of 64001000.spi failed with error -2
[ 29.640000] libphy: Fixed MDIO Bus: probed
[ 29.680000] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 29.690000] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 29.700000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 29.710000] ehci-pci: EHCI PCI platform driver
[ 29.720000] ehci-platform: EHCI generic platform driver
[ 29.750000] mousedev: PS/2 mouse device common for all mice
[ 29.790000] usbcore: registered new interface driver usbhid
[ 29.800000] usbhid: USB HID core driver
[ 29.820000] usbcore: registered new interface driver snd-usb-audio
[ 29.900000] NET: Registered protocol family 10
[ 29.960000] Segment Routing with IPv6
[ 29.960000] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 30.020000] NET: Registered protocol family 17
[ 30.020000] Key type dns_resolver registered
[ 30.070000] bootconsole [early0] uses init memory and must be disabled even before the real one is ready
[ 30.080000] bootconsole [early0] disabledSen jälkeen ei tapahdu mitään näkyvää.
Nyt voit yrittää käsitellä kolmea ongelmaa:
[ 23.980000] Initramfs unpacking failed: junk in compressed archive
...
[ 28.940000] sifive-serial 64000000.serial: unable to find controller clock
...
[ 29.610000] sifive_spi 64001000.spi: Unable to find bus clock...ja myös lopettaa tulostuksen konsoliin.
Ei ole ollenkaan vaikeaa voittaa kaksi taajuuksien ongelmaa: sinun on lisättävä pisteitä clocks tarvittavien laitteiden alipuihin, jotta solmulle annetaan selkeä nimike tlclk:
diff --git a/arch/riscv/dts/zeowaa-1gb.dts b/arch/riscv/dts/zeowaa-1gb.dts
index 4b2cebc..1347e76 100644
--- a/arch/riscv/dts/zeowaa-1gb.dts
+++ b/arch/riscv/dts/zeowaa-1gb.dts
@@ -96,6 +97,7 @@
L8: serial@64000000 {
compatible = "sifive,uart0";
interrupt-parent = <&L0>;
+ clocks = <&tlclk>;
interrupts = <2>;
reg = <0x64000000 0x1000>;
reg-names = "control";
@@ -107,6 +109,7 @@
interrupt-parent = <&L0>;
interrupts = <1>;
reg = <0x64001000 0x1000>;
+ clocks = <&tlclk>;
reg-names = "control";
L12: mmc@0 {
compatible = "mmc-spi-slot";
@@ -116,7 +119,7 @@
voltage-ranges = <3300 3300>;
};
};
- L11: tlclk {
+ tlclk: tlclk {
#clock-cells = <0>;
clock-frequency = <25000000>;
clock-output-names = "tlclk";Lisäämällä rivi #define pr_debug printk tiedoston alkuun init/initramfs.c, joka näyttää viestin roskista initramfs:n sijaan, saamme hieman yksityiskohtaisemman viestin:
[ 2.760000] Unpacking initramfs...
[ 2.770000] Detected gzip compressed data
[ 23.940000] Detected (null) compressed data
[ 23.970000] Initramfs unpacking failed: junk in compressed archiveEli ehkä roskaa ei ole sen sijasta initramfs ja вместе.
Okei, hän löysi jotain, ehkä se riittää. Mihin konsoli katosi? Haku antaa linkin ongelmaan Githubissa: — käy ilmi, ettei UART:sta yksin kuljettajan mukaan kannata edes puhua. Mutta päivätty 11. heinäkuuta 2018 - vuosi sitten. Kävi ilmi, että tämä sitoumus ei koskaan päässyt puuhun, josta rakennan ydintä. Asettamalla tämän korjaustiedoston manuaalisesti sain toimivan Linuxin! Kävi ilmi, että initramfs-ongelma ei todellakaan ollut kriittinen.
Kirjautuminen käyttäjä=root, salasana=sifive, onnistuin ilman ongelmia (paitsi ymmärsin, että GPIO-numerolla on kanta, josta kaikki lasketaan ja joka pitää vain lukea vastaavasta pseudotiedostosta) kautta sysfs sytyttää levyn LEDin.
Kuten viime kerralla, liitän mukaan tekstivideon Linuxin käynnistymisestä. Kun konsoli vaihtaa earlyprintk:stä normaaliin, tulee jonkinlaista roskaa, samanlaista kuin ulostulossa, kun UART-nopeus on asetettu väärin. Mielenkiintoista on, että pelaaja selvisi onnistuneesti tämän "sotun" läpi.
Lähde: will.com