AttÄlÄ Linux kodols sÅ«ta jums sveicienus, izmantojot GPIO.
Å ajÄ stÄsta daÄ¼Ä par RISC-V RocketChip pÄrneÅ”anu uz Ä·Ä«nieÅ”u plati ar Cyclone IV mÄs joprojÄm darbosimies Linux, kÄ arÄ« iemÄcÄ«simies paÅ”iem konfigurÄt IP Core atmiÅas kontrolieri un nedaudz rediÄ£Ät iekÄrtas DTS aprakstu. Å is raksts ir turpinÄjums , bet, atŔķirÄ«bÄ no diezgan plaÅ”Ä iepriekÅ”ÄjÄ, tas bÅ«s diezgan Ä«ss.
ā¦ TÄpÄc ka setup_smp izsauc tikai tad, ja kodols ir konfigurÄts ar SMP atbalstu, varat mÄÄ£inÄt atspÄjot daudzkodolu. BÅ«s nepatÄ«kami, ja atmiÅas modulÄ« bÅ«s jÄievieÅ” arÄ« atomitÄtes atbalsts (man Ŕķita, ka keÅ”atmiÅa pati par sevi lÄpÄ«), bet viena kodola gadÄ«jumÄ tam nevajadzÄtu mÅ«s traucÄt.
JoprojÄm nepacÄlÄs...
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Linux version 4.19.0-sifive-1+ (trosinenko@trosinenko-pc) (gcc version 8.3.0 (Buildroot 2019.02-07449-g4eddd28f99)) #1 Thu Jul 4 18:38:10 MSK 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] Initial ramdisk at: 0x(____ptrval____) (16777216 bytes)
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Normal [mem 0x00000000c0000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] software IO TLB: mapped [mem 0xbb1fc000-0xbf1fc000] (64MB)
[ 0.000000] Unable to find "cpu" devicetree entry
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055
[ 0.000000] Kernel command line: debug console=ttySIF0,125200 root=/dev/mmcblk0p2 loglevel=7 rootwait
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] BUG: Bad page state in process swapper pfn:80bf7
[ 0.000000] page:ffffffe03f029e08 count:0 mapcount:-65280 mapping:0000000000000000 index:0x1
[ 0.000000] flags: 0x0()
[ 0.000000] raw: 0000000000000000 0000000000000100 0000000000000200 0000000000000000
[ 0.000000] raw: 0000000000000001 0000000000000000 00000000ffff00ff
[ 0.000000] page dumped because: nonzero mapcount
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.19.0-sifive-1+ #1
[ 0.000000] Call Trace:
[ 0.000000] [<ffffffe00002cfde>] walk_stackframe+0x0/0xa0
[ 0.000000] [<ffffffe00002d1da>] show_stack+0x2a/0x34
[ 0.000000] [<ffffffe00063c898>] chachachllachachachTradeonachachach_inachachipachachachachllachachachTradeonachachachdevachachachypachachachllachachachTradeona+0x20/0x28
[ 0.000000] [<ffffffe00009499c>] bad_page+0xe4/0x102
[ 0.000000] [<ffffffe0000949f2>] free_pages_check_bad+0x38/0x7a
[ 0.000000] [<ffffffe000094bb0>] free_pcppages_bulk+0x106/0x36c
[ 0.000000] [<ffffffe0000957be>] free_unref_page_commit.isra.23+0x86/0x8e
[ 0.000000] [<ffffffe0000960bc>] free_unref_page+0x44/0x58
[ 0.000000] [<ffffffe0000960de>] __free_pages.part.28+0xe/0x22
[ 0.000000] [<ffffffe0000056da>] __free_pages_bootmem+0x86/0x90
[ 0.000000] [<ffffffe000007c46>] free_all_bootmem+0x156/0x1ba
[ 0.000000] [<ffffffe0000023f8>] mem_init+0x36/0x44
[ 0.000000] [<ffffffe0000007a0>] start_kernel+0x1aa/0x328
[ 0.000000] [<ffffffe000000058>] _sinittext+0x58/0x5c
[ 0.000000] Disabling lock debugging due to kernel taint
[ 0.000000] BUG: Bad page state in process swapper pfn:80bf9
[ 0.000000] page:ffffffe03f029e78 count:0 mapcount:-65280 mapping:0000000000000000 index:0x0
[ 0.000000] flags: 0x0()
[ 0.000000] raw: 0000000000000000 ffffffe03f020080 ffffffe03f020080 0000000000000000
[ 0.000000] raw: 0000000000000000 0000000000000000 00000000ffff00ff
[ 0.000000] page dumped because: nonzero mapcount
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Tainted: G B 4.19.0-sifive-1+ #1
[ 0.000000] Call Trace:
[ 0.000000] [<ffffffe00002cfde>] walk_stackframe+0x0/0xa0
[ 0.000000] [<ffffffe00002d1da>] show_stack+0x2a/0x34
[ 0.000000] [<ffffffe00063c898>] chachachllachachachTradeonachachach_inachachipachachachachllachachachTradeonachachachdevachachachypachachachllachachachTradeona+0x20/0x28
[ 0.000000] [<ffffffe00009499c>] bad_page+0xe4/0x102
[ 0.000000] [<ffffffe0000949f2>] free_pages_check_bad+0x38/0x7a
[ 0.000000] [<ffffffe0000955c6>] __free_pages_ok+0x3fe/0x430
[ 0.000000] [<ffffffe0000960ea>] __free_pages.part.28+0x1a/0x22
[ 0.000000] [<ffffffe0000056da>] __free_pages_bootmem+0x86/0x90
[ 0.000000] [<ffffffe000007c46>] free_all_bootmem+0x156/0x1ba
[ 0.000000] [<ffffffe0000023f8>] mem_init+0x36/0x44
[ 0.000000] [<ffffffe0000007a0>] start_kernel+0x1aa/0x328
[ 0.000000] [<ffffffe000000058>] _sinittext+0x58/0x5c
[ 0.000000] BUG: Bad page state in process swapper pfn:80bfa
[ 0.000000] page:ffffffe03f029eb0 count:0 mapcount:-65280 mapping:0000000000000000 index:0x0
[ 0.000000] flags: 0x0()
[ 0.000000] raw: 0000000000000000 ffffffe03f0200b8 ffffffe03f0200b8 0000000000000000
[ 0.000000] raw: 0000000000000000 0000000000000000 00000000ffff00ff
[ 0.000000] page dumped because: nonzero mapcount
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Tainted: G B 4.19.0-sifive-1+ #1
[ 0.000000] Call Trace:
[ 0.000000] [<ffffffe00002cfde>] walk_stackframe+0x0/0xa0
[ 0.000000] [<ffffffe00002d1da>] show_stack+0x2a/0x34
[ 0.000000] [<ffffffe00063c898>] chachachllachachachTradeonachachach_inachachipachachachachllachachachTradeonachachachdevachachachypachachachllachachachTradeona+0x20/0x28
[ 0.000000] [<ffffffe00009499c>] bad_page+0xe4/0x102
[ 0.000000] [<ffffffe0000949f2>] free_pages_check_bad+0x38/0x7a
[ 0.000000] [<ffffffe0000955c6>] __free_pages_ok+0x3fe/0x430
[ 0.000000] [<ffffffe0000960ea>] __free_pages.part.28+0x1a/0x22
[ 0.000000] [<ffffffe0000056da>] __free_pages_bootmem+0x86/0x90
[ 0.000000] [<ffffffe000007c46>] free_all_bootmem+0x156/0x1ba
[ 0.000000] [<ffffffe0000023f8>] mem_init+0x36/0x44
[ 0.000000] [<ffffffe0000007a0>] start_kernel+0x1aa/0x328
[ 0.000000] [<ffffffe000000058>] _sinittext+0x58/0x5c
[ 0.000000] BUG: Bad page state in process swapper pfn:80bfb
[ 0.000000] page:ffffffe03f029ee8 count:0 mapcount:-65280 mapping:0000000000000000 index:0x0
[ 0.000000] flags: 0x0()
[ 0.000000] raw: 0000000000000000 ffffffe03f0200f0 ffffffe03f0200f0 0000000000000000
[ 0.000000] raw: 0000000000000000 0000000000000000 00000000ffff00ff
[ 0.000000] page dumped because: nonzero mapcount
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Tainted: G B 4.19.0-sifive-1+ #1
[ 0.000000] Call Trace:
[ 0.000000] [<ffffffe00002cfde>] walk_stackframe+0x0/0xa0
[ 0.000000] [<ffffffe00002d1da>] show_stack+0x2a/0x34
[ 0.000000] [<ffffffe00063c898>] chachachllachachachTradeonachachach_inachachipachachachachllachachachTradeonachachachdevachachachypachachachllachachachTradeona+0x20/0x28
[ 0.000000] [<ffffffe00009499c>] bad_page+0xe4/0x102
[ 0.000000] [<ffffffe0000949f2>] free_pages_check_bad+0x38/0x7a
[ 0.000000] [<ffffffe0000955c6>] __free_pages_ok+0x3fe/0x430
[ 0.000000] [<ffffffe0000960ea>] __free_pages.part.28+0x1a/0x22
[ 0.000000] [<ffffffe0000056da>] __free_pages_bootmem+0x86/0x90
[ 0.000000] [<ffffffe000007c46>] free_all_bootmem+0x156/0x1ba
[ 0.000000] [<ffffffe0000023f8>] mem_init+0x36/0x44
[ 0.000000] [<ffffffe0000007a0>] start_kernel+0x1aa/0x328
[ 0.000000] [<ffffffe000000058>] _sinittext+0x58/0x5c
[ 0.000000] BUG: Bad page state in process swapper pfn:80bfc
[ 0.000000] page:ffffffe03f029f20 count:0 mapcount:-65280 mapping:0000000000000000 index:0x0
[ 0.000000] flags: 0x0()
[ 0.000000] raw: 0000000000000000 ffffffe03f020028 ffffffe03f020028 0000000000000000
[ 0.000000] raw: 0000000000000000 0000000000000000 00000000ffff00ff
...Interesanti, ka pÄc visas atkļūdoÅ”anas es nolÄmu apskatÄ«t, kÄ vajadzÄtu izskatÄ«ties kodola āatsaucesā izvadei, viÅÅ” teica. make qemu, un konstatÄja lÄ«dzÄ«gu kļūdu.
DiemžÄl nÄkamais lÄ«menis (Linux kodols) ir sarežģītÄks: GDB, kas savienots caur JTAG ar RocketChip, acÄ«mredzot darbojas ar fiziskÄm adresÄm neatkarÄ«gi no tÄ, kÄ ir konfigurÄts MMU, un kodols, kas mÅ«s interesÄ Å”obrÄ«d, jau ir konfigurÄjis displeju. adresÄm, tÄpÄc to ir viegli pateikt display/10i $pc tas neizdosies - mÄs redzÄsim tikai daudz unimp. Bet, ja mÄs jau esam izdomÄjuÅ”i nobÄ«di (Ŕķiet, ka 0x80200000 -> 0xffffffe000000000), tad jÅ«s varat krÄpties:
1: x/10i $pc
=> 0xffffffe000002436 <setup_smp>: unimp
0xffffffe000002438 <setup_smp+2>: unimp
0xffffffe00000243a <setup_smp+4>: unimp
0xffffffe00000243c <setup_smp+6>: unimp
0xffffffe00000243e <setup_smp+8>: unimp
0xffffffe000002440 <setup_smp+10>: unimp
0xffffffe000002442 <setup_smp+12>: unimp
0xffffffe000002444 <setup_smp+14>: unimp
0xffffffe000002446 <setup_smp+16>: unimp
0xffffffe000002448 <setup_smp+18>: unimp
(gdb) undisplay 1
(gdb) display/10i ($pc - 0xffffffe000002436 + 0x80202436)
2: x/10i ($pc - 0xffffffe000002436 + 0x80202436)
0x80202436: addi sp,sp,-96
0x80202438: sd s0,80(sp)
0x8020243a: sd s1,72(sp)
0x8020243c: sd s2,64(sp)
0x8020243e: sd s3,56(sp)
0x80202440: sd s4,48(sp)
0x80202442: sd s5,40(sp)
0x80202444: sd s6,32(sp)
0x80202446: sd s7,24(sp)
0x80202448: sd s8,16(sp)PÄrtraukuma punkti tiek iestatÄ«ti tÄdÄ paÅ”Ä veidÄ:
(gdb) p setup_smp
$1 = {<text variable, no debug info>} 0xffffffe000002436 <setup_smp>
(gdb) b *0x80202436
Breakpoint 1 at 0x80202436
(gdb) c
Continuing.
Program received signal SIGTRAP, Trace/breakpoint trap.
setup_smp () at /home/trosinenko/freedom-u-sdk/linux/arch/riscv/kernel/smpboot.c:58
58 while ((dn = of_find_node_by_type(dn, "cpu"))) {
(gdb) bt
#0 setup_smp () at /home/trosinenko/freedom-u-sdk/linux/arch/riscv/kernel/smpboot.c:58
#1 0xffffffe0000022a2 in setup_arch () at /home/trosinenko/freedom-u-sdk/linux/arch/riscv/kernel/setup.c:253
#2 0x0000000000000000 in ?? ()
Backtrace stopped: frame did not save the PCBet jums tie ir manuÄli jÄnoÅem, lai tiktu tÄlÄk - GDB tas ir kaut kÄds pilnÄ«gi nesaprotams lamatas. Ak jÄ, ja gadÄs teikt s vai n nevis si, gdb mÄÄ£inÄs ievietot netieÅ”u pÄrtraukuma punktu, kas acÄ«mredzamu iemeslu dÄļ netiks iestatÄ«ts, taÄu GDB nevar atturÄt. Bet nesteidzieties pÄrstartÄt dÄli - pÄc maniem novÄrojumiem, pietiek ar restartÄÅ”anu tikai gdb (Åemiet vÄrÄ, ka vecie pÄrtraukuma punkti var nepazust).
PatiesÄ«bÄ jums bÅ«s jÄrisina sÄkotnÄjÄ problÄma: atkļūdoÅ”anas izvietoÅ”ana printk par funkciju of_find_node_by_type, ko izmanto sÄknÄÅ”anas procesora kodola meklÄÅ”anas kods, parÄda, ka tas redz kaut kÄdus atkritumus, nevis ierÄ«Äu tipu nosaukumus. PiemÄram, tas no kaut kurienes paÅem rindu āSerial portā, lai gan tas acÄ«mredzami nav dtb laukÄ device_type. MeklÄjot Å”os baitus kodola attÄlÄ, es tos atradu, apskatÄ«ju nobÄ«di un sapratu acÄ«mredzamo: kodola izmÄrs sÄknÄÅ”anas parametros ir skaidri novÄrtÄts par zemu: tam ir atvÄlÄti 8 Mb, bet tas aizÅem vairÄk nekÄ desmit. PieŔķīru 16Mb, bet dÄ«vainÄ«bas neapstÄjÄs. PÄc dejoÅ”anas ar FDT nolasÄ«Å”anu no dažÄdÄm adresÄm (parasti adrese tiek pÄrsÅ«tÄ«ta uz kodolu reÄ£istrÄ a1), beidzot nolÄmu izsekot, bet ko tagad tur tas ir parsÄts. Par laimi, tÄ vietÄ, lai staigÄtu ar atkļūdotÄju (un mÄs atceramies, ka ar adreÅ”u tulkoÅ”anu ir nianses, kuras joprojÄm ir jÄatrisina tÄ vai citÄdi), varat vienkÄrÅ”i un Ätri iedziļinÄties failÄ drivers/of/fdt.c precizÄt #define pr_debug printk. RezultÄts bija:
pievienojot atkļūdoŔanas izvadi
diff --git a/arch/riscv/kernel/setup.c b/arch/riscv/kernel/setup.c
index 3db0d71d128b..fac47df9d1db 100644
--- a/arch/riscv/kernel/setup.c
+++ b/arch/riscv/kernel/setup.c
@@ -173,6 +173,7 @@ asmlinkage void __init setup_vm(void)
void __init parse_dtb(unsigned int hartid, void *dtb)
{
+ printk("HART = %u DTB = %lxn", hartid, dtb);
early_init_dt_scan(__va(dtb));
}
diff --git a/drivers/of/base.c b/drivers/of/base.c
index 74eaedd5b860..c019e4158e1d 100644
--- a/drivers/of/base.c
+++ b/drivers/of/base.c
@@ -940,10 +940,12 @@ struct device_node *of_find_node_by_type(struct device_node *from,
unsigned long flags;
raw_spin_lock_irqsave(&devtree_lock, flags);
- for_each_of_allnodes_from(from, np)
+ for_each_of_allnodes_from(from, np) {
+ printk("%lx %lx [%s] | [%s]n", from, np, np->type, type);
if (np->type && (of_node_cmp(np->type, type) == 0)
&& of_node_get(np))
break;
+ }
of_node_put(from);
raw_spin_unlock_irqrestore(&devtree_lock, flags);
return np;
diff --git a/drivers/of/fdt.c b/drivers/of/fdt.c
index 800ad252cf9c..2b45870ebada 100644
--- a/drivers/of/fdt.c
+++ b/drivers/of/fdt.c
@@ -31,6 +31,8 @@
#include "of_private.h"
+#define pr_debug printk
+
/*
* of_fdt_limit_memory - limit the number of regions in the /memory node
* @limit: maximum entries
@@ -1253,6 +1255,7 @@ bool __init early_init_dt_scan(void *params)
*/
void __init unflatten_device_tree(void)
{
+ printk("INITIAL: %lxn", initial_boot_params);
__unflatten_device_tree(initial_boot_params, NULL, &of_root,
early_init_dt_alloc_memory_arch, false);Izvade uz aparatūru
SIFIVE, INC.
5555555555555555555555555
5555 5555
5555 5555
5555 5555
5555 5555555555555555555555
5555 555555555555555555555555
5555 5555
5555 5555
5555 5555
5555555555555555555555555555 55555
55555 555555555 55555
55555 55555 55555
55555 5 55555
55555 55555
55555 55555
55555 55555
55555 55555
55555 55555
555555555
55555
5
SiFive RISC-V Core IP
{
#address-cells = <0x00000001>;
#size-cells = <0x00000001>;
compatible = "freechips,rocketchip-unknown-dev";
model = "freechips,rocketchip-unknown";
chosen {
linux,initrd-start = <0x82000000>;
riscv,kernel-end = <0x81200000>;
riscv,kernel-start = <0x80200000>;
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
bootargs = <0x64656275 0x6720636f 0x6e736f6c 0x653d7474 0x79534946 0x302c3132 0x35323030 0x20726f6f 0x743d2f64 0x65762f6d 0x6d63626c 0x6b307032 0x206c6f67 0x6c657665 0x6c3d3720 0x726f6f74 0x77616974>;
}
firmware {
sifive,uboot = "YYYY-MM-DD";
}
aliases {
serial0 = <0x2f736f63 0x2f736572 0x69616c40 0x36343030 0x30303030>;
}
cpus {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
cpu@0 {
device_type = "cpu";
clock-frequency = <0x00000000>;
compatible = "sifive,rocket0", "riscv";
d-cache-block-size = <0x00000010>;
d-cache-sets = <0x00000040>;
d-cache-size = <0x00001000>;
d-tlb-sets = <0x00000001>;
d-tlb-size = <0x00000020>;
i-cache-block-size = <0x00000010>;
i-cache-sets = <0x00000040>;
i-cache-size = <0x00001000>;
i-tlb-sets = <0x00000001>;
i-tlb-size = <0x00000020>;
mmu-type = "riscv,sv39";
next-level-cache = <0x00000001>;
reg = <0x00000000>;
riscv,isa = "rv64imafdc";
status = "okay";
timebase-frequency = <0x000f4240>;
tlb-split;
interrupt-controller {
#interrupt-cells = <0x00000001>;
compatible = "riscv,cpu-intc";
interrupt-controller;
phandle = <0x00000002>;
}
}
}
ram@80000000 {
device_type = "memory";
reg = <0x80000000 0x40000000>;
reg-names = "mem";
phandle = <0x00000001>;
}
soc {
#address-cells = <0x00000001>;
#size-cells = <0x00000001>;
compatible = "freechips,rocketchip-unknown-soc", "simple-bus";
ranges;
clint@2000000 {
compatible = "riscv,clint0";
interrupts-extended = <0x00000002 0x00000003 0x00000002 0x00000007>;
reg = <0x02000000 0x00010000>;
reg-names = "control";
}
debug-controller@0 {
compatible = "sifive,debug-013", "riscv,debug-013";
interrupts-extended = <0x00000002 0x0000ffff>;
reg = <0x00000000 0x00001000>;
reg-names = "control";
}
gpio@64002000 {
#gpio-cells = <0x00000002>;
#interrupt-cells = <0x00000002>;
compatible = "sifive,gpio0";
gpio-controller;
interrupt-controller;
interrupt-parent = <0x00000003>;
interrupts = <0x00000003 0x00000004 0x00000005 0x00000006 0x00000007 0x00000008>;
reg = <0x64002000 0x00001000>;
reg-names = "control";
}
interrupt-controller@c000000 {
#interrupt-cells = <0x00000001>;
compatible = "riscv,plic0";
interrupt-controller;
interrupts-extended = <0x00000002 0x0000000b 0x00000002 0x00000009>;
reg = <0x0c000000 0x04000000>;
reg-names = "control";
riscv,max-priority = <0x00000007>;
riscv,ndev = <0x00000008>;
phandle = <0x00000003>;
}
rom@10000 {
compatible = "sifive,maskrom0";
reg = <0x00010000 0x00002000>;
reg-names = "mem";
}
serial@64000000 {
compatible = "sifive,uart0";
interrupt-parent = <0x00000003>;
interrupts = <0x00000002>;
reg = <0x64000000 0x00001000>;
reg-names = "control";
}
spi@64001000 {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
compatible = "sifive,spi0";
interrupt-parent = <0x00000003>;
interrupts = <0x00000001>;
reg = <0x64001000 0x00001000>;
reg-names = "control";
mmc@0 {
compatible = "mmc-spi-slot";
disable-wp;
reg = <0x00000000>;
spi-max-frequency = <0x01312d00>;
voltage-ranges = <0x00000ce4 0x00000ce4>;
}
}
tlclk {
#clock-cells = <0x00000000>;
clock-frequency = <0x017d7840>;
clock-output-names = "tlclk";
compatible = "fixed-clock";
}
}
}
[ 0.000000] HART = 0 DTB = 81200000
[ 0.000000] search "chosen", depth: 0, uname:
[ 0.000000] search "chosen", depth: 1, uname: chosen
[ 0.000000] Looking for initrd properties...
[ 0.000000] Command line is: debug console=ttySIF0,125200 root=/dev/mmcblk0p2 loglevel=7 rootwait
[ 0.000000] dt_root_size_cells = 1
[ 0.000000] dt_root_addr_cells = 1
[ 0.000000] memory scan node ram@80000000, reg size 8,
[ 0.000000] - 80000000 , 40000000
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Linux version 4.19.0-sifive-1+ (trosinenko@trosinenko-pc) (gcc version 8.3.0 (Buildroot 2019.02-07449-g4eddd28f99)) #1 SMP Sat Jul 6 12:14:41 MSK 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Normal [mem 0x00000000c0000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] INITIAL: ffffffe001000000
[ 0.000000] -> unflatten_device_tree()
[ 0.000000] Unflattening device tree:
[ 0.000000] magic: d00dfeed
[ 0.000000] size: 00001000
[ 0.000000] version: 00000011
[ 0.000000] size is 13512, allocating...
[ 0.000000] unflattening (____ptrval____)...
[ 0.000000] fixed up name for ->
[ 0.000000] fixed up name for chosen -> chosen
[ 0.000000] fixed up name for firmware -> firmware
[ 0.000000] fixed up name for aliases -> aliases
[ 0.000000] fixed up name for cpus -> cpus
[ 0.000000] fixed up name for cpu@0 -> cpu
[ 0.000000] fixed up name for interrupt-controller -> interrupt-controller
[ 0.000000] fixed up name for ram@80000000 -> ram
[ 0.000000] fixed up name for soc -> soc
[ 0.000000] fixed up name for clint@2000000 -> clint
[ 0.000000] fixed up name for debug-controller@0 -> debug-controller
[ 0.000000] fixed up name for gpio@64002000 -> gpio
[ 0.000000] fixed up name for interrupt-controller@c000000 -> interrupt-controller
[ 0.000000] fixed up name for rom@10000 -> rom
[ 0.000000] fixed up name for serial@64000000 -> serial
[ 0.000000] fixed up name for spi@64001000 -> spi
[ 0.000000] fixed up name for mmc@0 -> mmc
[ 0.000000] fixed up name for tlclk -> tlclk
[ 0.000000] <- unflatten_device_tree()
[ 0.000000] software IO TLB: mapped [mem 0xbb1fc000-0xbf1fc000] (64MB)
[ 0.000000] 0 ffffffe03effcab0 [attach() failed for %s with error %d
[ 0.000000] ] | [cpu]
[ 0.000000] 0 ffffffe03eff0020 [(null)] | [cpu]Izvade uz QEMU
SIFIVE, INC.
5555555555555555555555555
5555 5555
5555 5555
5555 5555
5555 5555555555555555555555
5555 555555555555555555555555
5555 5555
5555 5555
5555 5555
5555555555555555555555555555 55555
55555 555555555 55555
55555 55555 55555
55555 5 55555
55555 55555
55555 55555
55555 55555
55555 55555
55555 55555
555555555
55555
5
SiFive RISC-V Core IP
{
#address-cells = <0x00000002>;
#size-cells = <0x00000002>;
compatible = "riscv-virtio";
model = "riscv-virtio,qemu";
chosen {
linux,initrd-start = <0x00000000 0x88000000>;
linux,initrd-end = <0x00000000 0x88442b86>;
riscv,kernel-start = <0x00000000 0x80200000>;
riscv,kernel-end = <0x00000000 0x80c482ac>;
bootargs = "";
stdout-path = <0x2f756172 0x74403130 0x30303030>;
}
uart@10000000 {
interrupts = <0x0000000a>;
interrupt-parent = <0x00000002>;
clock-frequency = <0x00384000>;
reg = <0x00000000 0x10000000 0x00000000 0x00000100>;
compatible = "ns16550a";
}
test@100000 {
reg = <0x00000000 0x00100000 0x00000000 0x00001000>;
compatible = "sifive,test0";
}
virtio_mmio@10008000 {
interrupts = <0x00000008>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10008000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10007000 {
interrupts = <0x00000007>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10007000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10006000 {
interrupts = <0x00000006>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10006000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10005000 {
interrupts = <0x00000005>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10005000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10004000 {
interrupts = <0x00000004>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10004000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10003000 {
interrupts = <0x00000003>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10003000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10002000 {
interrupts = <0x00000002>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10002000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10001000 {
interrupts = <0x00000001>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10001000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
cpus {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
timebase-frequency = <0x00989680>;
cpu@0 {
device_type = "cpu";
reg = <0x00000000>;
status = "okay";
compatible = "riscv";
riscv,isa = "rv64imafdcsu";
mmu-type = "riscv,sv48";
clock-frequency = <0x3b9aca00>;
interrupt-controller {
#interrupt-cells = <0x00000001>;
interrupt-controller;
compatible = "riscv,cpu-intc";
linux,phandle = <0x00000001>;
phandle = <0x00000001>;
}
}
}
memory@80000000 {
device_type = "memory";
reg = <0x00000000 0x80000000 0x00000000 0x40000000>;
}
soc {
#address-cells = <0x00000002>;
#size-cells = <0x00000002>;
compatible = "simple-bus";
ranges;
pci@30000000 {
interrupt-map-mask = <0x00001800 0x00000000 0x00000000 0x00000007>;
interrupt-map = <0x00000000 0x00000000 0x00000000 0x00000001 0x00000002 0x00000020 0x00000000 0x00000000 0x00000000 0x00000002 0x00000002 0x00000021 0x00000000 0x00000000 0x00000000 0x00000003 0x00000002 0x00000022 0x00000000 0x00000000 0x00000000 0x00000004 0x00000002 0x00000023 0x00000800 0x00000000 0x00000000 0x00000001 0x00000002 0x00000021 0x00000800 0x00000000 0x00000000 0x00000002 0x00000002 0x00000022 0x00000800 0x00000000 0x00000000 0x00000003 0x00000002 0x00000023 0x00000800 0x00000000 0x00000000 0x00000004 0x00000002 0x00000020 0x00001000 0x00000000 0x00000000 0x00000001 0x00000002 0x00000022 0x00001000 0x00000000 0x00000000 0x00000002 0x00000002 0x00000023 0x00001000 0x00000000 0x00000000 0x00000003 0x00000002 0x00000020 0x00001000 0x00000000 0x00000000 0x00000004 0x00000002 0x00000021 0x00001800 0x00000000 0x00000000 0x00000001 0x00000002 0x00000023 0x00001800 0x00000000 0x00000000 0x00000002 0x00000002 0x00000020 0x00001800 0x00000000 0x00000000 0x00000003 0x00000002 0x00000021 0x00001800 0x00000000 0x00000000 0x00000004 0x00000002 0x00000022>;
ranges = <0x01000000 0x00000000 0x00000000 0x00000000 0x03000000 0x00000000 0x00010000 0x02000000 0x00000000 0x40000000 0x00000000 0x40000000 0x00000000 0x40000000>;
reg = <0x00000000 0x30000000 0x00000000 0x10000000>;
dma-coherent;
bus-range = <0x00000000 0x000002ff>;
linux,pci-domain = <0x00000000>;
device_type = "pci";
compatible = "pci-host-ecam-generic";
#size-cells = <0x00000002>;
#interrupt-cells = <0x00000001>;
#address-cells = <0x00000003>;
}
interrupt-controller@c000000 {
linux,phandle = <0x00000002>;
phandle = <0x00000002>;
riscv,ndev = <0x00000035>;
riscv,max-priority = <0x00000007>;
reg-names = "control";
reg = <0x00000000 0x0c000000 0x00000000 0x04000000>;
interrupts-extended = <0x00000001 0x0000000b 0x00000001 0x00000009>;
interrupt-controller;
compatible = "riscv,plic0";
#interrupt-cells = <0x00000001>;
#address-cells = <0x00000000>;
}
clint@2000000 {
interrupts-extended = <0x00000001 0x00000003 0x00000001 0x00000007>;
reg = <0x00000000 0x02000000 0x00000000 0x00010000>;
compatible = "riscv,clint0";
}
}
}
[ 0.000000] HART = 0 DTB = 80e00000
[ 0.000000] search "chosen", depth: 0, uname:
[ 0.000000] search "chosen", depth: 1, uname: chosen
[ 0.000000] Looking for initrd properties...
[ 0.000000] initrd_start=0x88000000 initrd_end=0x88442b86
[ 0.000000] Command line is: earlyprintk
[ 0.000000] dt_root_size_cells = 2
[ 0.000000] dt_root_addr_cells = 2
[ 0.000000] memory scan node memory@80000000, reg size 16,
[ 0.000000] - 80000000 , 40000000
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Linux version 4.19.0-sifive-1+ (trosinenko@trosinenko-pc) (gcc version 8.3.0 (Buildroot 2019.02-07449-g4eddd28f99)) #1 SMP Sat Jul 6 12:14:41 MSK 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] Initial ramdisk at: 0x(____ptrval____) (4467590 bytes)
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Normal [mem 0x00000000c0000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] INITIAL: ffffffe000c00000
[ 0.000000] -> unflatten_device_tree()
[ 0.000000] Unflattening device tree:
[ 0.000000] magic: d00dfeed
[ 0.000000] size: 00000d56
[ 0.000000] version: 00000011
[ 0.000000] size is 14192, allocating...
[ 0.000000] unflattening (____ptrval____)...
[ 0.000000] fixed up name for ->
[ 0.000000] fixed up name for chosen -> chosen
[ 0.000000] fixed up name for uart@10000000 -> uart
[ 0.000000] fixed up name for test@100000 -> test
[ 0.000000] fixed up name for virtio_mmio@10008000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10007000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10006000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10005000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10004000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10003000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10002000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10001000 -> virtio_mmio
[ 0.000000] fixed up name for cpus -> cpus
[ 0.000000] fixed up name for cpu@0 -> cpu
[ 0.000000] fixed up name for interrupt-controller -> interrupt-controller
[ 0.000000] fixed up name for memory@80000000 -> memory
[ 0.000000] fixed up name for soc -> soc
[ 0.000000] fixed up name for pci@30000000 -> pci
[ 0.000000] fixed up name for interrupt-controller@c000000 -> interrupt-controller
[ 0.000000] fixed up name for clint@2000000 -> clint
[ 0.000000] <- unflatten_device_tree()
[ 0.000000] software IO TLB: mapped [mem 0xbb1fc000-0xbf1fc000] (64MB)
[ 0.000000] 0 ffffffe03effc808 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effca78 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effcd98 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd068 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd230 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd4b8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd740 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd9c8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effdc50 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effded8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe160 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe3e8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe670 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe888 [cpu] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03effec00 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03effeee8 [memory] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff0b0 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff320 [pci] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff858 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efffd58 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effc808 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effca78 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effcd98 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd068 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd230 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd4b8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd740 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd9c8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effdc50 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effded8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe160 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe3e8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe670 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe888 [cpu] | [cpu]
[ 0.000000] elf_hwcap is 0x112d
[ 0.000000] percpu: Embedded 17 pages/cpu @(____ptrval____) s29400 r8192 d32040 u69632
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055
[ 0.000000] Kernel command line: earlyprintk
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 949716K/1046528K available (6565K kernel code, 342K rwdata, 2564K rodata, 208K init, 832K bss, 96812K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[ 0.000000] plic: mapped 53 interrupts to 2 (out of 2) handlers.
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x24e6a1710, max_idle_ns: 440795202120 ns
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] bootconsole [early0] disabled
[ 0.000000] HART = 0 DTB = 80e00000
[ 0.000000] search "chosen", depth: 0, uname:
[ 0.000000] search "chosen", depth: 1, uname: chosen
[ 0.000000] Looking for initrd properties...
[ 0.000000] initrd_start=0x88000000 initrd_end=0x88442b86
[ 0.000000] Command line is: earlyprintk
[ 0.000000] dt_root_size_cells = 2
[ 0.000000] dt_root_addr_cells = 2
[ 0.000000] memory scan node memory@80000000, reg size 16,
[ 0.000000] - 80000000 , 40000000
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Linux version 4.19.0-sifive-1+ (trosinenko@trosinenko-pc) (gcc version 8.3.0 (Buildroot 2019.02-07449-g4eddd28f99)) #1 SMP Sat Jul 6 12:14:41 MSK 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] Initial ramdisk at: 0x(____ptrval____) (4467590 bytes)
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Normal [mem 0x00000000c0000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] INITIAL: ffffffe000c00000
[ 0.000000] -> unflatten_device_tree()
[ 0.000000] Unflattening device tree:
[ 0.000000] magic: d00dfeed
[ 0.000000] size: 00000d56
[ 0.000000] version: 00000011
[ 0.000000] size is 14192, allocating...
[ 0.000000] unflattening (____ptrval____)...
[ 0.000000] fixed up name for ->
[ 0.000000] fixed up name for chosen -> chosen
[ 0.000000] fixed up name for uart@10000000 -> uart
[ 0.000000] fixed up name for test@100000 -> test
[ 0.000000] fixed up name for virtio_mmio@10008000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10007000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10006000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10005000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10004000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10003000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10002000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10001000 -> virtio_mmio
[ 0.000000] fixed up name for cpus -> cpus
[ 0.000000] fixed up name for cpu@0 -> cpu
[ 0.000000] fixed up name for interrupt-controller -> interrupt-controller
[ 0.000000] fixed up name for memory@80000000 -> memory
[ 0.000000] fixed up name for soc -> soc
[ 0.000000] fixed up name for pci@30000000 -> pci
[ 0.000000] fixed up name for interrupt-controller@c000000 -> interrupt-controller
[ 0.000000] fixed up name for clint@2000000 -> clint
[ 0.000000] <- unflatten_device_tree()
[ 0.000000] software IO TLB: mapped [mem 0xbb1fc000-0xbf1fc000] (64MB)
[ 0.000000] 0 ffffffe03effc808 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effca78 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effcd98 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd068 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd230 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd4b8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd740 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd9c8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effdc50 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effded8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe160 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe3e8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe670 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe888 [cpu] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03effec00 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03effeee8 [memory] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff0b0 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff320 [pci] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff858 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efffd58 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effc808 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effca78 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effcd98 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd068 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd230 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd4b8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd740 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd9c8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effdc50 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effded8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe160 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe3e8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe670 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe888 [cpu] | [cpu]
[ 0.000000] elf_hwcap is 0x112d
[ 0.000000] percpu: Embedded 17 pages/cpu @(____ptrval____) s29400 r8192 d32040 u69632
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055
[ 0.000000] Kernel command line: earlyprintk
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 949716K/1046528K available (6565K kernel code, 342K rwdata, 2564K rodata, 208K init, 832K bss, 96812K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[ 0.000000] plic: mapped 53 interrupts to 2 (out of 2) handlers.
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x24e6a1710, max_idle_ns: 440795202120 ns
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] bootconsole [early0] disabled
[ 0.000000] Calibrating delay loop (skipped), value calculated using timer frequency.. 20.00 BogoMIPS (lpj=100000)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.000000] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.020000] rcu: Hierarchical SRCU implementation.
[ 0.020000] smp: Bringing up secondary CPUs ...
[ 0.020000] smp: Brought up 1 node, 1 CPU
[ 0.050000] devtmpfs: initialized
[ 0.050000] 0 ffffffe03effc808 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effca78 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effcd98 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effd068 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effd230 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effd4b8 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effd740 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effd9c8 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effdc50 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effded8 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effe160 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effe3e8 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effe670 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effe888 [cpu] | [cpu]
[ 0.050000] random: get_random_u32 called from bucket_table_alloc+0x76/0x17a with crng_init=0
[ 0.050000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.050000] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.060000] NET: Registered protocol family 16
[ 0.090000] vgaarb: loaded
[ 0.090000] SCSI subsystem initialized
[ 0.090000] usbcore: registered new interface driver usbfs
[ 0.090000] usbcore: registered new interface driver hub
[ 0.090000] usbcore: registered new device driver usb
[ 0.090000] pps_core: LinuxPPS API ver. 1 registered
[ 0.090000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 0.090000] PTP clock support registered
[ 0.100000] Advanced Linux Sound Architecture Driver Initialized.
[ 0.100000] clocksource: Switched to clocksource riscv_clocksource
[ 0.110000] NET: Registered protocol family 2
[ 0.110000] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes)
[ 0.110000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.110000] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 0.110000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.110000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.110000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.110000] NET: Registered protocol family 1
[ 0.120000] Unpacking initramfs...
[ 0.590000] workingset: timestamp_bits=62 max_order=18 bucket_order=0
[ 0.620000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.620000] io scheduler noop registered
[ 0.620000] io scheduler deadline registered
[ 0.620000] io scheduler cfq registered (default)
[ 0.620000] io scheduler mq-deadline registered
[ 0.620000] io scheduler kyber registered
[ 0.620000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 0.690000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.690000] 10000000.uart: ttyS0 at MMIO 0x10000000 (irq = 10, base_baud = 230400) is a 16550A
[ 0.720000] console [ttyS0] enabled
[ 0.720000] [drm] radeon kernel modesetting enabled.
[ 0.720000] [drm] amdgpu kernel modesetting enabled.
[ 0.730000] loop: module loaded
[ 0.730000] libphy: Fixed MDIO Bus: probed
[ 0.740000] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 0.740000] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 0.740000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.740000] ehci-pci: EHCI PCI platform driver
[ 0.740000] ehci-platform: EHCI generic platform driver
[ 0.740000] mousedev: PS/2 mouse device common for all mice
[ 0.740000] usbcore: registered new interface driver usbhid
[ 0.740000] usbhid: USB HID core driver
[ 0.740000] usbcore: registered new interface driver snd-usb-audio
[ 0.740000] NET: Registered protocol family 10
[ 0.750000] Segment Routing with IPv6
[ 0.750000] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 0.750000] NET: Registered protocol family 17
[ 0.750000] Key type dns_resolver registered
[ 0.760000] ALSA device list:
[ 0.760000] No soundcards found.
[ 0.770000] Freeing unused kernel memory: 208K
[ 0.770000] This architecture does not have kernel memory protection.
[ 0.770000] Run /init as init process(āLaika zÄ«mogaā rindas izvada kodols, pirms tÄm koku izvada BBL) No vienas puses, FDT tiek veiksmÄ«gi nolasÄ«ts, no otras puses, parsÄtajÄ tiek iegÅ«tas kaut kÄdas muļķības. objektsā koks.
AtkļūdoÅ”anas procesa laikÄ es sapratu, ka BBL nevar nolasÄ«t ādubultoā adresi nevis tÄpÄc, ka konfigurÄcijÄ bÅ«tu kļūda, bet vienkÄrÅ”i tÄpÄc, ka saknes mezglam bija #address-cells = <1>; #size-cells = <1>;.
PaplaÅ”inot atkļūdoÅ”anas izvadi, es redzÄju, ka tas norÄda uz type Šø name āpiesistsā, un diezgan dÄ«vainÄ veidÄ: viÅu pirmais baits (sÄkot no nulles) tika atiestatÄ«ts uz nulli, kaut kas lÄ«dzÄ«gs 0xabcdef -> 0xab00ef. NÄcÄs izmantot pazÄ«stamu taktiku: zinot adreses, kur atrodas bojÄtÄ atmiÅa, pievienojiet to funkcijai printk izdrukÄt Å”os datus. Nu paÅ”i izaicinÄjumi printk izkaisÄ«t tos tur, kur to ir maz. DiemžÄl tas nav kļuvis daudz skaidrÄks. Tad es sÄku konsultÄties ar izjauktajiem objdump versiju, manuÄli iestatiet pÄrtraukuma punktus un soli pa solim izejiet cauri problemÄtiskajai koda sadaļai. Un tad atklÄjÄs noslÄpumaina un nepatÄ«kama lieta: ja es uzreiz nolikÅ”u pÄrtraukuma punktu kaut kur salÄ«dzinoÅ”i tÄlu no zinÄmÄ-labÄ stÄvokļa, tad, pie tÄ apstÄjoties, ieraudzÄ«Å”u jau sabojÄto atmiÅu. Bet, ja jÅ«s mÄÄ£inÄt klusi piezagties viÅai soli pa solim, kļūdai izdodas paslÄpties! Tas smaržo pÄc bojÄta atmiÅas kontrollera un keÅ”atmiÅas, kas slÄpj kļūdu, ja pastÄvÄ«gi pieprasÄt nepiecieÅ”amo vÄrtÄ«bu. Ko darÄ«t, jaā¦
AtmiÅas nomaiÅa
PieÄ·Äries iespÄjai atrisinÄt problÄmu, kas nebija manÄ pusÄ, pieÅÄmu, ka varbÅ«t tikko esmu saÅÄmis saplÄ«suÅ”u atmiÅas karti. Tad atcerÄjos, ka desmit gadus vecs netbook ir ne tikai portatÄ«vais dators, bet arÄ« vÄrtÄ«gs DDR2 SO-DIMM avots. KÄ bonusu varat tajÄ ievietot no tÄfeles noÅemto atmiÅu un panÄkt, lai Memtest gandrÄ«z uzreiz uzkaras (starp citu, Linux ielÄdÄts gandrÄ«z lÄ«dz grafiskajam apvalkam. Bet labÄk neatkÄrtot Å”o eksperimentu, ja novÄrtÄjat informÄciju par uzstÄdÄ«tajiem diskiem...). No vienas puses, mÄs varam pieÅemt, ka atmiÅa vienkÄrÅ”i nederÄja Å”im konkrÄtajam netbook. No otras puses, viÅÅ” varÄja boot! Bija cerÄ«ba, ka atmiÅa vienkÄrÅ”i ir āsalauztaā, un problÄma nebija manÄ iesaiÅojumÄ.
Tas nozÄ«mÄ, ka jums ir jÄmÄÄ£ina Ä«slaicÄ«gi palaist ar netbook atmiÅu. DiemžÄl Quartus 18 nezina, kÄ uzlabot Å”o IP Core, lai to varÄtu rediÄ£Ät. Tas nozÄ«mÄ, ka beidzot ir pienÄcis laiks iemÄcÄ«ties izveidot jaunas instances. Viss izrÄdÄ«jÄs pavisam vienkÄrÅ”i: mÄs IP katalogÄ meklÄjam vienumu DDR2 SDRAM Controller ar ALTMEMPHY Intel FPGA IP un iegÅ«stam bloku ar tÄdu paÅ”u interfeisu kÄ iepriekÅ”. VienÄ«gÄ problÄma ir pareizo atmiÅas iestatÄ«jumu iestatÄ«Å”ana.
AtmiÅas moduļa parametru iegÅ«Å”ana
Ir samÄrÄ skaidrs veids, kÄ konfigurÄt moduli: nolasÄ«t parametrus no SPD. PatieÅ”Äm, ja parasts dators nolasa SPD datus un, pamatojoties uz tiem, konfigurÄ kontrolieri, tad atÅemsim Å”os datus par esoÅ”o netbook un ievadÄ«sim tabulÄ.
Tas tiek darÄ«ts Ubuntu : jums ir jÄinstalÄ pakotne i2c-tools, slodzes moduļi eeprom Šø i2c-i801 (TomÄr neesmu pÄrliecinÄts, ka otrs Å”oferis strÄdÄs visur), tad skrien decode-dimms:
dekodÄt-dimms izvadi
# decode-dimms version 6231 (2014-02-20 10:54:34 +0100)
Memory Serial Presence Detect Decoder
By Philip Edelbrock, Christian Zuckschwerdt, Burkart Lingner,
Jean Delvare, Trent Piepho and others
Decoding EEPROM: /sys/bus/i2c/drivers/eeprom/0-0050
Guessing DIMM is in bank 1
---=== SPD EEPROM Information ===---
EEPROM Checksum of bytes 0-62 OK (0x00)
SPD Revision Invalid
Fundamental Memory type Unknown (0x00)
---=== Manufacturing Information ===---
Manufacturer Undefined
Part Number Undefined
Decoding EEPROM: /sys/bus/i2c/drivers/eeprom/4-0050
Guessing DIMM is in bank 1
---=== SPD EEPROM Information ===---
EEPROM Checksum of bytes 0-62 OK (0x00)
SPD Revision Invalid
Fundamental Memory type Unknown (0x00)
---=== Manufacturing Information ===---
Manufacturer Undefined
Part Number Undefined
Decoding EEPROM: /sys/bus/i2c/drivers/eeprom/6-0050
Guessing DIMM is in bank 1
---=== SPD EEPROM Information ===---
EEPROM Checksum of bytes 0-62 OK (0x76)
# of bytes written to SDRAM EEPROM 128
Total number of bytes in EEPROM 256
Fundamental Memory type DDR2 SDRAM
SPD Revision 1.2
---=== Memory Characteristics ===---
Maximum module speed 800 MHz (PC2-6400)
Size 1024 MB
Banks x Rows x Columns x Bits 8 x 13 x 10 x 64
Ranks 2
SDRAM Device Width 16 bits
Module Height 30.0 mm
Module Type SO-DIMM (67.6 mm)
DRAM Package Planar
Voltage Interface Level SSTL 1.8V
Module Configuration Type No Parity
Refresh Rate Reduced (7.8 us) - Self Refresh
Supported Burst Lengths 4, 8
tCL-tRCD-tRP-tRAS 6-6-6-18
Supported CAS Latencies (tCL) 6T, 5T, 4T
Minimum Cycle Time 2.50 ns at CAS 6 (tCK min)
3.00 ns at CAS 5
3.75 ns at CAS 4
Maximum Access Time 0.40 ns at CAS 6 (tAC)
0.45 ns at CAS 5
0.50 ns at CAS 4
Maximum Cycle Time (tCK max) 8.00 ns
---=== Timing Parameters ===---
Address/Command Setup Time Before Clock (tIS) 0.17 ns
Address/Command Hold Time After Clock (tIH) 0.25 ns
Data Input Setup Time Before Strobe (tDS) 0.05 ns
Data Input Hold Time After Strobe (tDH) 0.12 ns
Minimum Row Precharge Delay (tRP) 15.00 ns
Minimum Row Active to Row Active Delay (tRRD) 10.00 ns
Minimum RAS# to CAS# Delay (tRCD) 15.00 ns
Minimum RAS# Pulse Width (tRAS) 45.00 ns
Write Recovery Time (tWR) 15.00 ns
Minimum Write to Read CMD Delay (tWTR) 7.50 ns
Minimum Read to Pre-charge CMD Delay (tRTP) 7.50 ns
Minimum Active to Auto-refresh Delay (tRC) 60.00 ns
Minimum Recovery Delay (tRFC) 127.50 ns
Maximum DQS to DQ Skew (tDQSQ) 0.20 ns
Maximum Read Data Hold Skew (tQHS) 0.30 ns
---=== Manufacturing Information ===---
Manufacturer Samsung
Manufacturing Location Code 0x02
Part Number M4 70T2864QZ3-CF7
Revision Code 0x3351
Manufacturing Date 2009-W34
Assembly Serial Number 0x79C64E9A
Number of SDRAM DIMMs detected and decoded: 3ProblÄma ir tÄ, ka daži laiki Å”eit nav norÄdÄ«ti, tÄpÄc iesim otro ceļu.
Kas ir rakstīts uz mūsu moduļiem:
Å ajÄ gadÄ«jumÄ interesantÄks ir uzraksts uz paÅ”Äm atmiÅas mikroshÄmÄm: K4T1G164QQ-HCF7. Ierakstot Å”o rindiÅu Google, mÄs iegÅ«stam vairÄku desmitu lapu datu lapu ar visiem nepiecieÅ”amajiem parametriem, ko var glÄ«ti iekļaut IP Core rekvizÄ«tos. VienkÄrÅ”i pievÄrsiet uzmanÄ«bu mÄrvienÄ«bÄm: kaut kur ns, kaut kur - ps, un dažreiz pat dalÄs tCK. Es jums nemÄcÄ«Å”u, kam pievÄrst uzmanÄ«bu - daudzas lietas es pats konfigurÄju nejauÅ”i (es nevaru garantÄt, ka Å”ÄdÄ veidÄ nevar āsadedzinÄtā atmiÅu vai FPGA). Es tikai vÄrÅ”u jÅ«su uzmanÄ«bu uz to: es nevarÄju panÄkt, lai kontrolieris darbotos ļoti ilgu laiku, un pÄdÄjais solis bija sapratne, ka man ir jÄpÄrbauda visu atmiÅas saskarÅu platums, lai nodroÅ”inÄtu atbilstÄ«bu Ä£enerÄtajam Verilog kodam. : galu galÄ, kad iekÅ”Ä MemIfBundle norÄdÄ«ts val mem_ba = IO(Output(UInt(2.W))), un ir 8 bankas (t.i. 3 bitu plata adrese), tad mums ir tikai izeja no atmiÅas kontrollera, kas karÄjas gaisÄ - problÄma, bet ne kritiska, tÄpÄc viss ir sintezÄts, bet nedarbojas.
IespÄjams, viss darbotos ar veco moduli, ja tiktu atjauninÄts kontrolleris, taÄu pagaidÄm esmu pÄrÄk slinks, lai tiktu galÄ ar iespÄjamÄm peldoÅ”Äm kļūdÄm: man paÅ”am pietiek.
TÄtad, pÄc pÄrcelÅ”anÄs timebase-frequency DTS no konkrÄtÄ CPU lÄ«meÅa uz mezgla lÄ«meni cpus (saskaÅÄ ar diezgan saprotamo kodola pieprasÄ«jumu), mÄs iegÅ«stam:
SlÄpts teksts
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Linux version 4.19.0-sifive-1+ (trosinenko@trosinenko-pc) (gcc version 8.3.0 (Buildroot 2019.02-07449-g4eddd28f99)) #1 SMP Tue Jul 9 22:42:36 MSK 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] Initial ramdisk at: 0x(____ptrval____) (16777216 bytes)
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Normal [mem 0x00000000c0000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] software IO TLB: mapped [mem 0xbb1fc000-0xbf1fc000] (64MB)
[ 0.000000] elf_hwcap is 0x112d
[ 0.000000] percpu: Embedded 17 pages/cpu @(____ptrval____) s29400 r8192 d32040 u69632
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055
[ 0.000000] Kernel command line: debug console=ttySIF0,125200 root=/dev/mmcblk0p2 loglevel=7 rootwait
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 937696K/1046528K available (6565K kernel code, 343K rwdata, 2564K rodata, 208K init, 832K bss, 108832K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[ 0.000000] plic: mapped 8 interrupts to 1 (out of 2) handlers.
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
[ 0.020000] pid_max: default: 32768 minimum: 301
[ 0.030000] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.040000] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.140000] rcu: Hierarchical SRCU implementation.
[ 0.190000] smp: Bringing up secondary CPUs ...
[ 0.190000] smp: Brought up 1 node, 1 CPU
[ 0.220000] devtmpfs: initialized
[ 0.300000] random: get_random_u32 called from bucket_table_alloc+0x76/0x17a with crng_init=0
[ 0.330000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.340000] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.380000] NET: Registered protocol family 16
[ 1.850000] vgaarb: loaded
[ 1.870000] SCSI subsystem initialized
[ 1.900000] usbcore: registered new interface driver usbfs
[ 1.910000] usbcore: registered new interface driver hub
[ 1.920000] usbcore: registered new device driver usb
[ 1.930000] pps_core: LinuxPPS API ver. 1 registered
[ 1.940000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 1.950000] PTP clock support registered
[ 1.970000] Advanced Linux Sound Architecture Driver Initialized.
[ 2.010000] clocksource: Switched to clocksource riscv_clocksource
[ 2.600000] NET: Registered protocol family 2
[ 2.640000] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes)
[ 2.650000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 2.670000] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 2.700000] TCP: Hash tables configured (established 8192 bind 8192)
[ 2.720000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 2.730000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 2.750000] NET: Registered protocol family 1
[ 2.770000] Unpacking initramfs...
[ 23.980000] Initramfs unpacking failed: junk in compressed archive
[ 24.030000] workingset: timestamp_bits=62 max_order=18 bucket_order=0
[ 25.020000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 25.030000] io scheduler noop registered
[ 25.040000] io scheduler deadline registered
[ 25.050000] io scheduler cfq registered (default)
[ 25.060000] io scheduler mq-deadline registered
[ 25.060000] io scheduler kyber registered
[ 25.120000] sifive_gpio 64002000.gpio: SiFive GPIO chip registered 6 GPIOs
[ 25.150000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 28.870000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 28.940000] sifive-serial 64000000.serial: unable to find controller clock
[ 28.950000] sifive-serial: probe of 64000000.serial failed with error -2
[ 28.980000] [drm] radeon kernel modesetting enabled.
[ 28.990000] [drm] amdgpu kernel modesetting enabled.
[ 29.500000] loop: module loaded
[ 29.610000] sifive_spi 64001000.spi: Unable to find bus clock
[ 29.620000] sifive_spi: probe of 64001000.spi failed with error -2
[ 29.640000] libphy: Fixed MDIO Bus: probed
[ 29.680000] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 29.690000] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 29.700000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 29.710000] ehci-pci: EHCI PCI platform driver
[ 29.720000] ehci-platform: EHCI generic platform driver
[ 29.750000] mousedev: PS/2 mouse device common for all mice
[ 29.790000] usbcore: registered new interface driver usbhid
[ 29.800000] usbhid: USB HID core driver
[ 29.820000] usbcore: registered new interface driver snd-usb-audio
[ 29.900000] NET: Registered protocol family 10
[ 29.960000] Segment Routing with IPv6
[ 29.960000] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 30.020000] NET: Registered protocol family 17
[ 30.020000] Key type dns_resolver registered
[ 30.070000] bootconsole [early0] uses init memory and must be disabled even before the real one is ready
[ 30.080000] bootconsole [early0] disabledPÄc tam nekas redzams nenotiek.
Tagad varat mÄÄ£inÄt tikt galÄ ar trim problÄmÄm:
[ 23.980000] Initramfs unpacking failed: junk in compressed archive
...
[ 28.940000] sifive-serial 64000000.serial: unable to find controller clock
...
[ 29.610000] sifive_spi 64001000.spi: Unable to find bus clock...un arī aptur izvadi uz konsoli.
Nepavisam nav grÅ«ti pÄrvarÄt divas problÄmas ar frekvencÄm: jums jÄpievieno punkti clocks nepiecieÅ”amo ierÄ«Äu apakÅ”kokos, ÄrtÄ«bai pieŔķirot mezglam skaidru etiÄ·etes nosaukumu tlclk:
diff --git a/arch/riscv/dts/zeowaa-1gb.dts b/arch/riscv/dts/zeowaa-1gb.dts
index 4b2cebc..1347e76 100644
--- a/arch/riscv/dts/zeowaa-1gb.dts
+++ b/arch/riscv/dts/zeowaa-1gb.dts
@@ -96,6 +97,7 @@
L8: serial@64000000 {
compatible = "sifive,uart0";
interrupt-parent = <&L0>;
+ clocks = <&tlclk>;
interrupts = <2>;
reg = <0x64000000 0x1000>;
reg-names = "control";
@@ -107,6 +109,7 @@
interrupt-parent = <&L0>;
interrupts = <1>;
reg = <0x64001000 0x1000>;
+ clocks = <&tlclk>;
reg-names = "control";
L12: mmc@0 {
compatible = "mmc-spi-slot";
@@ -116,7 +119,7 @@
voltage-ranges = <3300 3300>;
};
};
- L11: tlclk {
+ tlclk: tlclk {
#clock-cells = <0>;
clock-frequency = <25000000>;
clock-output-names = "tlclk";Pievienojot rindu #define pr_debug printk lÄ«dz faila sÄkumam init/initramfs.c, kurÄ initramfs vietÄ tiek parÄdÄ«ts ziÅojums par atkritumu, mÄs saÅemam nedaudz detalizÄtÄku ziÅojumu:
[ 2.760000] Unpacking initramfs...
[ 2.770000] Detected gzip compressed data
[ 23.940000] Detected (null) compressed data
[ 23.970000] Initramfs unpacking failed: junk in compressed archiveTas ir, iespÄjams, atkritumi nav nevis initramfs, un Š²Š¼ŠµŃŃŠµ.
Labi, viÅÅ” kaut ko atrada, varbÅ«t ar to pietiek. Kur pazuda konsole? MeklÄÅ”ana sniedz saiti uz problÄmu vietnÄ Github: ā izrÄdÄs, ka par UART vien, pÄc Å”ofera domÄm, pat runÄt nav vÄrts. Bet datÄts ar 11. gada 2018. jÅ«liju ā pirms gada. IzrÄdÄ«jÄs, ka Ŕī apÅemÅ”anÄs nekad nav iekļuvusi kokÄ, no kura es veidoju kodolu. ManuÄli uzliekot Å”o ielÄpu, es saÅÄmu strÄdÄjoÅ”u Linux! IzrÄdÄ«jÄs, ka problÄma ar initramfs tieÅ”Äm nebija kritiska.
Ielogoties kÄ user=root, password=sifive, varÄju bez problÄmÄm (izÅemot sapratni, ka GPIO numuram ir bÄze, no kuras viss tiek aprÄÄ·inÄts un kas tikai jÄnolasa no atbilstoÅ”Ä pseido faila) cauri sysfs iedegas LED uz tÄfeles.
TÄpat kÄ iepriekÅ”Äjo reizi, es pievienoju teksta video par Linux palaiÅ”anu. Kad konsole pÄrslÄdzas no earlyprintk uz standarta, parÄdÄs sava veida atkritumi, lÄ«dzÄ«gi kÄ izvadÄ, ja UART Ätrums ir iestatÄ«ts nepareizi. Interesanti, ka spÄlÄtÄjs veiksmÄ«gi tika galÄ ar Å”o "putru".
Avots: www.habr.com