Muchinyorwa chanhasi ndinoda kugoverana newe chirongwa chitsva. Panguva ino inobata switch ine girazi pani. Mudziyo wacho wakakwana, kuyera 42x42mm (standard glass panels ine dimensions 80x80mm). Nhoroondo yechigadzirwa ichi yakatanga kare kare, rinenge gore rapfuura.
Sarudzo dzekutanga dzaive paatmega328 microcontroller, asi pakupedzisira zvese zvakapera nenRF52832 microcontroller.
Iyo yekubata chikamu chemudziyo inomhanya paTTP223 chips. Masensa ese ari maviri anopihwa nekukanganisa kumwe. Inofambiswa ne CR2477 bhatiri, kuburikidza ne boost converter pane TPS610981 chip | .
Chigadzirwa chacho chinoshandisa simba-off circuit uchishandisa munda-effect transistors. Mushure mekudzvanya bhatani, iyo microcontroller pachayo inobata simba rekutonga uye ipapo bhatani rinogona kushandiswa sevhisi modes (munyaya yangu, uku kubatanidza nemamwe madivayiri, kudzima simba uye kugadziridza kune marongero efekitori).
Kune 2 rgb LEDs yekuratidza nyika uye sevhisi modes. Piezo emitter yakawedzerwawo kutevedzera kudzvanya kana uchibata mabhatani ekubata uye inonzwika inotaridza masevhisi modes. Iwo maLED uye piezo emitter anogona kubatidzwa nekudzimwa pakufunga kwemushandisi. Izvi zvinoitwa kuburikidza neakangwara imba controller nekutumira mirairo kune tekinoroji sensors; mushandisi anogona zvakare kushandura nguva dzekutumira bhatiri kuchaja uye nhanho yechiratidzo zvakare kuburikidza neakangwara imba controller. Kana ndiri ini .
Kushandiswa mukutumira modhi i7mA (250kbit, 10ms), kunwa mukurara i40Β΅A, kunwiwa munzvimbo isingasviki 1Β΅A (= kushandiswa kweiyo boost converter mu "isire" modhi). Rx, tx, swd connector yepurogiramu inopihwa. A miniature 2x3p connector ine pitch ye1.27 inoshandiswa. A special adapter inogadzirirwa programming.
Senguva dzose, kushanda kwechigadzirwa kunobva pane protocol . Iyi yekubata switch yakarongwa kuti ishandiswe mu roller blind control system. Asi kazhinji, iko kushandiswa kunogumira chete nefungidziro yako. Semuenzaniso, mwanakomana wangu (ane makore manomwe) atoita 7 mirairo yekuchinja shanduro: kubatidza uye kudzima mwenje muchimbuzi nebhavhu (inozokwidziridzwa pasi kubva pasi), kubatidza mwenje mune mukoridho wakareba uye wakasviba paunenge uchienda kuchimbuzi nebhavhu, uye imwe sepadivi pemubhedha, nekukasira kubatidza mwenje mumba mako kuitira kuti zvikara zvitize.
Mhosva yacho yaiwanzodhindwa paSLA printer, mudziyo wacho idiki, nyaya yacho yakazova diki, kushandiswa kweiyi tekinoroji yekudhinda kwakarurama.
Ona yakadhindwa modhi
Magnet anonamirwa mukesi uye bhatiri remukati chivharo.
Mavhidhiyo ane bvunzo dzemudziyo uyu:
Kune avo vanoda kudzokorora:
Yedza chirongwa kodhi yekuchinja mune roller bofu yekudzora system yeArduino IDE
Arduino Wiring
int8_t timer_status = 0;
boolean sens_flag1 = 0;
boolean sens_flag2 = 0;
boolean switch_a = 0;
boolean switch_b = 0;
uint16_t temp;
float vcc;
int battery;
int old_battery;
uint32_t oldmillis;
uint32_t newmillis;
uint32_t interrupt_time;
uint32_t SLEEP_TIME = 7000;
uint32_t SLEEP_TIME_W;
uint32_t SLEEP_TIME_W2;
int NrfRSSI;
uint16_t NrfRSSI2;
boolean wait_off;
//#define MY_DEBUG
#define MY_DISABLED_SERIAL
#define MY_RADIO_NRF5_ESB
#define MY_PASSIVE_NODE
#define MY_NODE_ID 120
#define MY_PARENT_NODE_ID 0
#define MY_PARENT_NODE_IS_STATIC
#define MY_TRANSPORT_UPLINK_CHECK_DISABLED
#define POWER_CHILD_ID 110
#define UP_POWER_SWITCH_ID 1
#define DOWN_POWER_SWITCH_ID 2
#define CHILD_ID_nRF52_RSSI_RX 3
#define BAT_COOF 0.0092957746478873
#define BAT_MIN 200
#define BAT_MAX 290
#include <MySensors.h>
MyMessage upMsg(UP_POWER_SWITCH_ID, V_STATUS);
MyMessage downMsg(DOWN_POWER_SWITCH_ID, V_STATUS);
MyMessage powerMsg(POWER_CHILD_ID, V_VAR1);
MyMessage msgRF52RssiReceiv(CHILD_ID_nRF52_RSSI_RX, V_VAR1);
void preHwInit() {
pinMode(31, OUTPUT); //power management pin
digitalWrite(31, HIGH);
delay(3000);
pinMode(3, INPUT); // on off mode button
pinMode(25, OUTPUT); // sens1 led
pinMode(26, OUTPUT); // sens1 led
pinMode(27, OUTPUT); // sens1 led
pinMode(6, OUTPUT); // sens21 led
pinMode(7, OUTPUT); // sens2 led
pinMode(8, OUTPUT); // sens2 led
pinMode(28, OUTPUT); // bizzer
pinMode(2, INPUT); // common interrupt for touch sensors
pinMode(9, INPUT); // touch sensors1
pinMode(10, INPUT); //touch sensors2
pinMode(29, INPUT); // battery
digitalWrite(28, LOW);
digitalWrite(27, HIGH);
digitalWrite(26, HIGH);
digitalWrite(25, HIGH);
digitalWrite(6, HIGH);
digitalWrite(7, HIGH);
digitalWrite(8, HIGH);
}
void before()
{
NRF_POWER->DCDCEN = 1;
analogReadResolution(12);
disableNfc();
turnOffAdc();
digitalWrite(25, LOW);
digitalWrite(6, LOW);
wait(200);
digitalWrite(25, HIGH);
digitalWrite(6, HIGH);
wait(100);
playSound0();
wait(100);
digitalWrite(25, LOW);
digitalWrite(6, LOW);
wait(200);
digitalWrite(25, HIGH);
digitalWrite(6, HIGH);
wait(3000);
digitalWrite(27, LOW);
digitalWrite(8, LOW);
wait(200);
digitalWrite(27, HIGH);
digitalWrite(8, HIGH);
wait(400);
digitalWrite(6, LOW);
digitalWrite(25, LOW);
wait(200);
digitalWrite(6, HIGH);
digitalWrite(25, HIGH);
wait(400);
digitalWrite(26, LOW);
digitalWrite(7, LOW);
wait(200);
digitalWrite(26, HIGH);
digitalWrite(7, HIGH);
wait(1000);
digitalWrite(26, LOW);
digitalWrite(7, LOW);
}
void setup()
{
digitalWrite(26, HIGH);
digitalWrite(7, HIGH);
wait(50);
playSound();
wait(2000);
readBatLev();
wait(200);
SLEEP_TIME_W = SLEEP_TIME;
}
void presentation()
{
sendSketchInfo("EFEKTA ON|OFF NODE 2CH", "1.0");
wait(100);
present(POWER_CHILD_ID, S_CUSTOM, "BATTERY DATA");
wait(100);
present(UP_POWER_SWITCH_ID, S_BINARY, "UP SWITCH");
wait(100);
present(DOWN_POWER_SWITCH_ID, S_BINARY, "DOWN SWITCH");
}
void loop()
{
if (sens_flag1 == 0 && sens_flag2 == 0) {
if (switch_a == 0 && switch_b == 0) {
timer_status = sleep(digitalPinToInterrupt(2), RISING, digitalPinToInterrupt(3), RISING, 3600000, false);
wait_off = 1;
} else {
//oldmillis = millis();
timer_status = sleep(digitalPinToInterrupt(2), RISING, digitalPinToInterrupt(3), RISING, SLEEP_TIME_W, false);
wait_off = 0;
}
}
if (timer_status == 3) {
wait(100);
digitalWrite(27, LOW);
digitalWrite(8, LOW);
wait(2000);
digitalWrite(27, HIGH);
digitalWrite(8, HIGH);
wait(100);
digitalWrite(31, LOW);
}
if (timer_status == 2) {
if (digitalRead(9) == HIGH && sens_flag1 == 0 && switch_b == 0) {
sens_flag1 = 1;
if (switch_a == 0) {
oldmillis = millis();
SLEEP_TIME_W = SLEEP_TIME;
switch_a = 1;
digitalWrite(6, LOW);
wait(10);
playSound1();
wait(20);
playSound2();
wait(50);
send(upMsg.set(switch_a));
wait(200);
} else {
switch_a = 0;
digitalWrite(6, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(upMsg.set(switch_a));
wait(200);
}
}
if (digitalRead(10) == HIGH && sens_flag2 == 0 && switch_a == 0) {
sens_flag2 = 1;
if (switch_b == 0) {
oldmillis = millis();
SLEEP_TIME_W = SLEEP_TIME;
switch_b = 1;
digitalWrite(25, LOW);
wait(10);
playSound1();
wait(20);
playSound2();
wait(50);
send(downMsg.set(switch_b));
wait(200);
} else {
switch_b = 0;
digitalWrite(25, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(downMsg.set(switch_b));
wait(200);
}
}
if (digitalRead(9) == LOW && sens_flag1 == 1) {
sens_flag1 = 0;
}
if (digitalRead(10) == LOW && sens_flag2 == 1) {
sens_flag2 = 0;
}
if (switch_a == 1 || switch_b == 1) {
if (wait_off == 0) {
newmillis = millis();
wait(10);
SLEEP_TIME_W2 = SLEEP_TIME_W;
wait(10);
interrupt_time = newmillis - oldmillis;
wait(10);
SLEEP_TIME_W = SLEEP_TIME_W2 - interrupt_time;
wait(10);
Serial.print("WAS IN A SLEEP: ");
Serial.print(newmillis - oldmillis);
Serial.println(" MILLISECONDS");
if (SLEEP_TIME_W < 1000) {
if (switch_a == 1) {
switch_a = 0;
digitalWrite(6, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(upMsg.set(switch_a));
wait(200);
}
if (switch_b == 1) {
switch_b = 0;
digitalWrite(25, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(downMsg.set(switch_b));
wait(200);
}
SLEEP_TIME_W = SLEEP_TIME;
wait(50);
}
Serial.println(SLEEP_TIME);
Serial.println(SLEEP_TIME_W);
Serial.println(SLEEP_TIME_W2);
Serial.print("GO TO SLEEP FOR: ");
Serial.print(SLEEP_TIME_W);
Serial.println(" MILLISECONDS");
}
oldmillis = millis();
}
}
if (timer_status == -1) {
if (switch_a == 1 || switch_b == 1) {
if (switch_a == 1) {
switch_a = 0;
digitalWrite(6, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(upMsg.set(switch_a));
wait(200);
}
if (switch_b == 1) {
switch_b = 0;
digitalWrite(25, HIGH);
wait(10);
playSound2();
wait(20);
playSound1();
wait(50);
send(downMsg.set(switch_b));
wait(200);
}
} else {
readBatLev();
}
}
}
void disableNfc() {
NRF_NFCT->TASKS_DISABLE = 1;
NRF_NVMC->CONFIG = 1;
NRF_UICR->NFCPINS = 0;
NRF_NVMC->CONFIG = 0;
}
void turnOffAdc() {
if (NRF_SAADC->ENABLE) {
NRF_SAADC->TASKS_STOP = 1;
while (NRF_SAADC->EVENTS_STOPPED) {}
NRF_SAADC->ENABLE = 0;
while (NRF_SAADC->ENABLE) {}
}
}
void myTone(uint32_t j, uint32_t k) {
j = 500000 / j;
k += millis();
while (k > millis()) {
digitalWrite(28, HIGH); delayMicroseconds(j);
digitalWrite(28, LOW ); delayMicroseconds(j);
}
}
void playSound0() {
myTone(1300, 50);
wait(20);
myTone(1300, 50);
wait(50);
}
void playSound() {
myTone(700, 30);
wait(10);
myTone(700, 30);
wait(10);
myTone(700, 30);
wait(50);
}
void playSound1() {
myTone(200, 10);
wait(10);
myTone(400, 5);
wait(30);
}
void playSound2() {
myTone(400, 10);
wait(10);
myTone(200, 5);
wait(30);
}
void readBatLev() {
temp = analogRead(29);
vcc = temp * 0.0033 * 100;
battery = map((int)vcc, BAT_MIN, BAT_MAX, 0, 100);
if (battery < 0) {
battery = 0;
}
if (battery > 100) {
battery = 100;
}
sendBatteryLevel(battery, 1);
wait(2000, C_INTERNAL, I_BATTERY_LEVEL);
send(powerMsg.set(temp));
wait(200);
NrfRSSI = transportGetReceivingRSSI();
NrfRSSI2 = map(NrfRSSI, -85, -40, 0, 100);
if (NrfRSSI2 < 0) {
NrfRSSI2 = 0;
}
if (NrfRSSI2 > 100) {
NrfRSSI2 = 100;
}
send(msgRF52RssiReceiv.set(NrfRSSI2));
wait(200);
}Mafaira enyaya mu stl -
Gerber PCB mafaira -
Pamibvunzo nezve budiriro iyi, nezve kuomerwa mubudiriro yako paArduinos neMysensors inogara ichiuya kuzonunura muhurukuro yedu yeteregiramu - .
Source: www.habr.com