Rasmda Linux yadrosi GPIO orqali sizga salomlar yuboradi.
RISC-V RocketChip-ni Cyclone IV bilan Xitoy platasiga o'tkazish haqidagi hikoyaning ushbu qismida biz hali ham Linux-ni ishga tushiramiz, shuningdek, IP Core xotira kontrollerini o'zimiz sozlashni va uskunaning DTS tavsifini biroz tahrirlashni o'rganamiz. Ushbu maqola davomidir , ammo, oldingisidan farqli o'laroq, u juda qisqa bo'ladi.
β¦ Chunki setup_smp Agar yadro SMP qo'llab-quvvatlashi bilan sozlangan bo'lsa, chaqiriladi, siz ko'p yadroni o'chirib ko'rishingiz mumkin. Xotira modulida atomiklikni qo'llab-quvvatlashni ham amalga oshirishim kerak bo'lsa, yoqimsiz bo'ladi (menga kesh bu bilan o'z-o'zidan ishlayotgandek tuyuldi), lekin bitta yadroli holatda bu bizga xalaqit bermasligi kerak.
Hali ham uchmadi...
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Linux version 4.19.0-sifive-1+ (trosinenko@trosinenko-pc) (gcc version 8.3.0 (Buildroot 2019.02-07449-g4eddd28f99)) #1 Thu Jul 4 18:38:10 MSK 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] Initial ramdisk at: 0x(____ptrval____) (16777216 bytes)
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Normal [mem 0x00000000c0000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] software IO TLB: mapped [mem 0xbb1fc000-0xbf1fc000] (64MB)
[ 0.000000] Unable to find "cpu" devicetree entry
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055
[ 0.000000] Kernel command line: debug console=ttySIF0,125200 root=/dev/mmcblk0p2 loglevel=7 rootwait
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] BUG: Bad page state in process swapper pfn:80bf7
[ 0.000000] page:ffffffe03f029e08 count:0 mapcount:-65280 mapping:0000000000000000 index:0x1
[ 0.000000] flags: 0x0()
[ 0.000000] raw: 0000000000000000 0000000000000100 0000000000000200 0000000000000000
[ 0.000000] raw: 0000000000000001 0000000000000000 00000000ffff00ff
[ 0.000000] page dumped because: nonzero mapcount
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.19.0-sifive-1+ #1
[ 0.000000] Call Trace:
[ 0.000000] [<ffffffe00002cfde>] walk_stackframe+0x0/0xa0
[ 0.000000] [<ffffffe00002d1da>] show_stack+0x2a/0x34
[ 0.000000] [<ffffffe00063c898>] chachachllachachachTradeonachachach_inachachipachachachachllachachachTradeonachachachdevachachachypachachachllachachachTradeona+0x20/0x28
[ 0.000000] [<ffffffe00009499c>] bad_page+0xe4/0x102
[ 0.000000] [<ffffffe0000949f2>] free_pages_check_bad+0x38/0x7a
[ 0.000000] [<ffffffe000094bb0>] free_pcppages_bulk+0x106/0x36c
[ 0.000000] [<ffffffe0000957be>] free_unref_page_commit.isra.23+0x86/0x8e
[ 0.000000] [<ffffffe0000960bc>] free_unref_page+0x44/0x58
[ 0.000000] [<ffffffe0000960de>] __free_pages.part.28+0xe/0x22
[ 0.000000] [<ffffffe0000056da>] __free_pages_bootmem+0x86/0x90
[ 0.000000] [<ffffffe000007c46>] free_all_bootmem+0x156/0x1ba
[ 0.000000] [<ffffffe0000023f8>] mem_init+0x36/0x44
[ 0.000000] [<ffffffe0000007a0>] start_kernel+0x1aa/0x328
[ 0.000000] [<ffffffe000000058>] _sinittext+0x58/0x5c
[ 0.000000] Disabling lock debugging due to kernel taint
[ 0.000000] BUG: Bad page state in process swapper pfn:80bf9
[ 0.000000] page:ffffffe03f029e78 count:0 mapcount:-65280 mapping:0000000000000000 index:0x0
[ 0.000000] flags: 0x0()
[ 0.000000] raw: 0000000000000000 ffffffe03f020080 ffffffe03f020080 0000000000000000
[ 0.000000] raw: 0000000000000000 0000000000000000 00000000ffff00ff
[ 0.000000] page dumped because: nonzero mapcount
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Tainted: G B 4.19.0-sifive-1+ #1
[ 0.000000] Call Trace:
[ 0.000000] [<ffffffe00002cfde>] walk_stackframe+0x0/0xa0
[ 0.000000] [<ffffffe00002d1da>] show_stack+0x2a/0x34
[ 0.000000] [<ffffffe00063c898>] chachachllachachachTradeonachachach_inachachipachachachachllachachachTradeonachachachdevachachachypachachachllachachachTradeona+0x20/0x28
[ 0.000000] [<ffffffe00009499c>] bad_page+0xe4/0x102
[ 0.000000] [<ffffffe0000949f2>] free_pages_check_bad+0x38/0x7a
[ 0.000000] [<ffffffe0000955c6>] __free_pages_ok+0x3fe/0x430
[ 0.000000] [<ffffffe0000960ea>] __free_pages.part.28+0x1a/0x22
[ 0.000000] [<ffffffe0000056da>] __free_pages_bootmem+0x86/0x90
[ 0.000000] [<ffffffe000007c46>] free_all_bootmem+0x156/0x1ba
[ 0.000000] [<ffffffe0000023f8>] mem_init+0x36/0x44
[ 0.000000] [<ffffffe0000007a0>] start_kernel+0x1aa/0x328
[ 0.000000] [<ffffffe000000058>] _sinittext+0x58/0x5c
[ 0.000000] BUG: Bad page state in process swapper pfn:80bfa
[ 0.000000] page:ffffffe03f029eb0 count:0 mapcount:-65280 mapping:0000000000000000 index:0x0
[ 0.000000] flags: 0x0()
[ 0.000000] raw: 0000000000000000 ffffffe03f0200b8 ffffffe03f0200b8 0000000000000000
[ 0.000000] raw: 0000000000000000 0000000000000000 00000000ffff00ff
[ 0.000000] page dumped because: nonzero mapcount
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Tainted: G B 4.19.0-sifive-1+ #1
[ 0.000000] Call Trace:
[ 0.000000] [<ffffffe00002cfde>] walk_stackframe+0x0/0xa0
[ 0.000000] [<ffffffe00002d1da>] show_stack+0x2a/0x34
[ 0.000000] [<ffffffe00063c898>] chachachllachachachTradeonachachach_inachachipachachachachllachachachTradeonachachachdevachachachypachachachllachachachTradeona+0x20/0x28
[ 0.000000] [<ffffffe00009499c>] bad_page+0xe4/0x102
[ 0.000000] [<ffffffe0000949f2>] free_pages_check_bad+0x38/0x7a
[ 0.000000] [<ffffffe0000955c6>] __free_pages_ok+0x3fe/0x430
[ 0.000000] [<ffffffe0000960ea>] __free_pages.part.28+0x1a/0x22
[ 0.000000] [<ffffffe0000056da>] __free_pages_bootmem+0x86/0x90
[ 0.000000] [<ffffffe000007c46>] free_all_bootmem+0x156/0x1ba
[ 0.000000] [<ffffffe0000023f8>] mem_init+0x36/0x44
[ 0.000000] [<ffffffe0000007a0>] start_kernel+0x1aa/0x328
[ 0.000000] [<ffffffe000000058>] _sinittext+0x58/0x5c
[ 0.000000] BUG: Bad page state in process swapper pfn:80bfb
[ 0.000000] page:ffffffe03f029ee8 count:0 mapcount:-65280 mapping:0000000000000000 index:0x0
[ 0.000000] flags: 0x0()
[ 0.000000] raw: 0000000000000000 ffffffe03f0200f0 ffffffe03f0200f0 0000000000000000
[ 0.000000] raw: 0000000000000000 0000000000000000 00000000ffff00ff
[ 0.000000] page dumped because: nonzero mapcount
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Tainted: G B 4.19.0-sifive-1+ #1
[ 0.000000] Call Trace:
[ 0.000000] [<ffffffe00002cfde>] walk_stackframe+0x0/0xa0
[ 0.000000] [<ffffffe00002d1da>] show_stack+0x2a/0x34
[ 0.000000] [<ffffffe00063c898>] chachachllachachachTradeonachachach_inachachipachachachachllachachachTradeonachachachdevachachachypachachachllachachachTradeona+0x20/0x28
[ 0.000000] [<ffffffe00009499c>] bad_page+0xe4/0x102
[ 0.000000] [<ffffffe0000949f2>] free_pages_check_bad+0x38/0x7a
[ 0.000000] [<ffffffe0000955c6>] __free_pages_ok+0x3fe/0x430
[ 0.000000] [<ffffffe0000960ea>] __free_pages.part.28+0x1a/0x22
[ 0.000000] [<ffffffe0000056da>] __free_pages_bootmem+0x86/0x90
[ 0.000000] [<ffffffe000007c46>] free_all_bootmem+0x156/0x1ba
[ 0.000000] [<ffffffe0000023f8>] mem_init+0x36/0x44
[ 0.000000] [<ffffffe0000007a0>] start_kernel+0x1aa/0x328
[ 0.000000] [<ffffffe000000058>] _sinittext+0x58/0x5c
[ 0.000000] BUG: Bad page state in process swapper pfn:80bfc
[ 0.000000] page:ffffffe03f029f20 count:0 mapcount:-65280 mapping:0000000000000000 index:0x0
[ 0.000000] flags: 0x0()
[ 0.000000] raw: 0000000000000000 ffffffe03f020028 ffffffe03f020028 0000000000000000
[ 0.000000] raw: 0000000000000000 0000000000000000 00000000ffff00ff
...Qizig'i shundaki, barcha disk raskadrovkalardan so'ng men "mos yozuvlar" yadro chiqishi qanday ko'rinishini ko'rib chiqishga qaror qildim, dedi u make qemu, va shunga o'xshash xatoni ko'rdim.
Afsuski, keyingi daraja (Linux yadrosi) ancha murakkab: JTAG orqali RocketChip-ga ulangan GDB, MMU qanday sozlanganidan qat'i nazar, jismoniy manzillar bilan ishlaydi va bizni qiziqtirgan yadro allaqachon displeyni sozlagan. manzillar, shuning uchun aytish oson display/10i $pc bu ishlamaydi - biz faqat ko'p narsani ko'ramiz unimp. Ammo agar biz ofsetni allaqachon aniqlagan bo'lsak (shunday tuyuladi 0x80200000 -> 0xffffffe000000000), keyin aldashingiz mumkin:
1: x/10i $pc
=> 0xffffffe000002436 <setup_smp>: unimp
0xffffffe000002438 <setup_smp+2>: unimp
0xffffffe00000243a <setup_smp+4>: unimp
0xffffffe00000243c <setup_smp+6>: unimp
0xffffffe00000243e <setup_smp+8>: unimp
0xffffffe000002440 <setup_smp+10>: unimp
0xffffffe000002442 <setup_smp+12>: unimp
0xffffffe000002444 <setup_smp+14>: unimp
0xffffffe000002446 <setup_smp+16>: unimp
0xffffffe000002448 <setup_smp+18>: unimp
(gdb) undisplay 1
(gdb) display/10i ($pc - 0xffffffe000002436 + 0x80202436)
2: x/10i ($pc - 0xffffffe000002436 + 0x80202436)
0x80202436: addi sp,sp,-96
0x80202438: sd s0,80(sp)
0x8020243a: sd s1,72(sp)
0x8020243c: sd s2,64(sp)
0x8020243e: sd s3,56(sp)
0x80202440: sd s4,48(sp)
0x80202442: sd s5,40(sp)
0x80202444: sd s6,32(sp)
0x80202446: sd s7,24(sp)
0x80202448: sd s8,16(sp)To'xtash nuqtalari xuddi shu tarzda o'rnatiladi:
(gdb) p setup_smp
$1 = {<text variable, no debug info>} 0xffffffe000002436 <setup_smp>
(gdb) b *0x80202436
Breakpoint 1 at 0x80202436
(gdb) c
Continuing.
Program received signal SIGTRAP, Trace/breakpoint trap.
setup_smp () at /home/trosinenko/freedom-u-sdk/linux/arch/riscv/kernel/smpboot.c:58
58 while ((dn = of_find_node_by_type(dn, "cpu"))) {
(gdb) bt
#0 setup_smp () at /home/trosinenko/freedom-u-sdk/linux/arch/riscv/kernel/smpboot.c:58
#1 0xffffffe0000022a2 in setup_arch () at /home/trosinenko/freedom-u-sdk/linux/arch/riscv/kernel/setup.c:253
#2 0x0000000000000000 in ?? ()
Backtrace stopped: frame did not save the PCAmmo davom etish uchun ularni qo'lda olib tashlashingiz kerak - GDB uchun bu mutlaqo tushunarsiz tuzoq. Ha, agar tasodifan aytsangiz s yoki n o'rniga si, gdb aniq sabablarga ko'ra o'rnatilmaydigan yashirin to'xtash nuqtasini qo'shishga harakat qiladi, lekin GDBni rad etishning hech qanday usuli yo'q. Ammo taxtani qayta ishga tushirishga shoshilmang - mening kuzatishlarimga ko'ra, faqat gdb-ni qayta ishga tushirish kifoya (esda tutingki, eski to'xtash nuqtalari yo'qolmasligi mumkin).
Aslida, siz asl muammoni hal qilishingiz kerak bo'ladi: disk raskadrovkani joylashtirish printk funksiyaga aylanadi of_find_node_by_type, yuklash protsessor yadrosi qidiruv kodi tomonidan ishlatiladigan qurilma turi nomlari o'rniga qandaydir axlatni ko'rishini ko'rsatadi. Masalan, u biron bir joydan "Serial port" qatorini oladi, garchi bu dtb maydonida aniq emas device_type. Ushbu baytlarni yadro tasvirida qidirib topib, men ularni topdim, ofsetni ko'rib chiqdim va aniq narsani angladim: yuklash parametrlarida yadro hajmi aniq kam baholangan: unga 8 Mb ajratilgan, lekin u o'ndan ortiq joyni oladi. Men 16Mb ajratdim, lekin g'alatilik to'xtamadi. Turli manzillardan FDT o'qish bilan raqsga tushgandan so'ng (odatda manzil registrdagi yadroga o'tkaziladi. a1), Men nihoyat kuzatishga qaror qildim, lekin nima ΡΠ΅ΠΉΡΠ°Ρ u erda tahlil qilingan. Yaxshiyamki, tuzatuvchi bilan yurish o'rniga (va biz eslaymizki, manzilni tarjima qilishda hali ham u yoki bu tarzda hal qilinishi kerak bo'lgan nuanslar mavjud), siz oddiygina va faylni qo'ltiq bilan bosib olishingiz mumkin. drivers/of/fdt.c belgilang #define pr_debug printk. Natijada:
disk raskadrovka chiqishini qo'shish
diff --git a/arch/riscv/kernel/setup.c b/arch/riscv/kernel/setup.c
index 3db0d71d128b..fac47df9d1db 100644
--- a/arch/riscv/kernel/setup.c
+++ b/arch/riscv/kernel/setup.c
@@ -173,6 +173,7 @@ asmlinkage void __init setup_vm(void)
void __init parse_dtb(unsigned int hartid, void *dtb)
{
+ printk("HART = %u DTB = %lxn", hartid, dtb);
early_init_dt_scan(__va(dtb));
}
diff --git a/drivers/of/base.c b/drivers/of/base.c
index 74eaedd5b860..c019e4158e1d 100644
--- a/drivers/of/base.c
+++ b/drivers/of/base.c
@@ -940,10 +940,12 @@ struct device_node *of_find_node_by_type(struct device_node *from,
unsigned long flags;
raw_spin_lock_irqsave(&devtree_lock, flags);
- for_each_of_allnodes_from(from, np)
+ for_each_of_allnodes_from(from, np) {
+ printk("%lx %lx [%s] | [%s]n", from, np, np->type, type);
if (np->type && (of_node_cmp(np->type, type) == 0)
&& of_node_get(np))
break;
+ }
of_node_put(from);
raw_spin_unlock_irqrestore(&devtree_lock, flags);
return np;
diff --git a/drivers/of/fdt.c b/drivers/of/fdt.c
index 800ad252cf9c..2b45870ebada 100644
--- a/drivers/of/fdt.c
+++ b/drivers/of/fdt.c
@@ -31,6 +31,8 @@
#include "of_private.h"
+#define pr_debug printk
+
/*
* of_fdt_limit_memory - limit the number of regions in the /memory node
* @limit: maximum entries
@@ -1253,6 +1255,7 @@ bool __init early_init_dt_scan(void *params)
*/
void __init unflatten_device_tree(void)
{
+ printk("INITIAL: %lxn", initial_boot_params);
__unflatten_device_tree(initial_boot_params, NULL, &of_root,
early_init_dt_alloc_memory_arch, false);Uskunada chiqish
SIFIVE, INC.
5555555555555555555555555
5555 5555
5555 5555
5555 5555
5555 5555555555555555555555
5555 555555555555555555555555
5555 5555
5555 5555
5555 5555
5555555555555555555555555555 55555
55555 555555555 55555
55555 55555 55555
55555 5 55555
55555 55555
55555 55555
55555 55555
55555 55555
55555 55555
555555555
55555
5
SiFive RISC-V Core IP
{
#address-cells = <0x00000001>;
#size-cells = <0x00000001>;
compatible = "freechips,rocketchip-unknown-dev";
model = "freechips,rocketchip-unknown";
chosen {
linux,initrd-start = <0x82000000>;
riscv,kernel-end = <0x81200000>;
riscv,kernel-start = <0x80200000>;
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
bootargs = <0x64656275 0x6720636f 0x6e736f6c 0x653d7474 0x79534946 0x302c3132 0x35323030 0x20726f6f 0x743d2f64 0x65762f6d 0x6d63626c 0x6b307032 0x206c6f67 0x6c657665 0x6c3d3720 0x726f6f74 0x77616974>;
}
firmware {
sifive,uboot = "YYYY-MM-DD";
}
aliases {
serial0 = <0x2f736f63 0x2f736572 0x69616c40 0x36343030 0x30303030>;
}
cpus {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
cpu@0 {
device_type = "cpu";
clock-frequency = <0x00000000>;
compatible = "sifive,rocket0", "riscv";
d-cache-block-size = <0x00000010>;
d-cache-sets = <0x00000040>;
d-cache-size = <0x00001000>;
d-tlb-sets = <0x00000001>;
d-tlb-size = <0x00000020>;
i-cache-block-size = <0x00000010>;
i-cache-sets = <0x00000040>;
i-cache-size = <0x00001000>;
i-tlb-sets = <0x00000001>;
i-tlb-size = <0x00000020>;
mmu-type = "riscv,sv39";
next-level-cache = <0x00000001>;
reg = <0x00000000>;
riscv,isa = "rv64imafdc";
status = "okay";
timebase-frequency = <0x000f4240>;
tlb-split;
interrupt-controller {
#interrupt-cells = <0x00000001>;
compatible = "riscv,cpu-intc";
interrupt-controller;
phandle = <0x00000002>;
}
}
}
ram@80000000 {
device_type = "memory";
reg = <0x80000000 0x40000000>;
reg-names = "mem";
phandle = <0x00000001>;
}
soc {
#address-cells = <0x00000001>;
#size-cells = <0x00000001>;
compatible = "freechips,rocketchip-unknown-soc", "simple-bus";
ranges;
clint@2000000 {
compatible = "riscv,clint0";
interrupts-extended = <0x00000002 0x00000003 0x00000002 0x00000007>;
reg = <0x02000000 0x00010000>;
reg-names = "control";
}
debug-controller@0 {
compatible = "sifive,debug-013", "riscv,debug-013";
interrupts-extended = <0x00000002 0x0000ffff>;
reg = <0x00000000 0x00001000>;
reg-names = "control";
}
gpio@64002000 {
#gpio-cells = <0x00000002>;
#interrupt-cells = <0x00000002>;
compatible = "sifive,gpio0";
gpio-controller;
interrupt-controller;
interrupt-parent = <0x00000003>;
interrupts = <0x00000003 0x00000004 0x00000005 0x00000006 0x00000007 0x00000008>;
reg = <0x64002000 0x00001000>;
reg-names = "control";
}
interrupt-controller@c000000 {
#interrupt-cells = <0x00000001>;
compatible = "riscv,plic0";
interrupt-controller;
interrupts-extended = <0x00000002 0x0000000b 0x00000002 0x00000009>;
reg = <0x0c000000 0x04000000>;
reg-names = "control";
riscv,max-priority = <0x00000007>;
riscv,ndev = <0x00000008>;
phandle = <0x00000003>;
}
rom@10000 {
compatible = "sifive,maskrom0";
reg = <0x00010000 0x00002000>;
reg-names = "mem";
}
serial@64000000 {
compatible = "sifive,uart0";
interrupt-parent = <0x00000003>;
interrupts = <0x00000002>;
reg = <0x64000000 0x00001000>;
reg-names = "control";
}
spi@64001000 {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
compatible = "sifive,spi0";
interrupt-parent = <0x00000003>;
interrupts = <0x00000001>;
reg = <0x64001000 0x00001000>;
reg-names = "control";
mmc@0 {
compatible = "mmc-spi-slot";
disable-wp;
reg = <0x00000000>;
spi-max-frequency = <0x01312d00>;
voltage-ranges = <0x00000ce4 0x00000ce4>;
}
}
tlclk {
#clock-cells = <0x00000000>;
clock-frequency = <0x017d7840>;
clock-output-names = "tlclk";
compatible = "fixed-clock";
}
}
}
[ 0.000000] HART = 0 DTB = 81200000
[ 0.000000] search "chosen", depth: 0, uname:
[ 0.000000] search "chosen", depth: 1, uname: chosen
[ 0.000000] Looking for initrd properties...
[ 0.000000] Command line is: debug console=ttySIF0,125200 root=/dev/mmcblk0p2 loglevel=7 rootwait
[ 0.000000] dt_root_size_cells = 1
[ 0.000000] dt_root_addr_cells = 1
[ 0.000000] memory scan node ram@80000000, reg size 8,
[ 0.000000] - 80000000 , 40000000
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Linux version 4.19.0-sifive-1+ (trosinenko@trosinenko-pc) (gcc version 8.3.0 (Buildroot 2019.02-07449-g4eddd28f99)) #1 SMP Sat Jul 6 12:14:41 MSK 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Normal [mem 0x00000000c0000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] INITIAL: ffffffe001000000
[ 0.000000] -> unflatten_device_tree()
[ 0.000000] Unflattening device tree:
[ 0.000000] magic: d00dfeed
[ 0.000000] size: 00001000
[ 0.000000] version: 00000011
[ 0.000000] size is 13512, allocating...
[ 0.000000] unflattening (____ptrval____)...
[ 0.000000] fixed up name for ->
[ 0.000000] fixed up name for chosen -> chosen
[ 0.000000] fixed up name for firmware -> firmware
[ 0.000000] fixed up name for aliases -> aliases
[ 0.000000] fixed up name for cpus -> cpus
[ 0.000000] fixed up name for cpu@0 -> cpu
[ 0.000000] fixed up name for interrupt-controller -> interrupt-controller
[ 0.000000] fixed up name for ram@80000000 -> ram
[ 0.000000] fixed up name for soc -> soc
[ 0.000000] fixed up name for clint@2000000 -> clint
[ 0.000000] fixed up name for debug-controller@0 -> debug-controller
[ 0.000000] fixed up name for gpio@64002000 -> gpio
[ 0.000000] fixed up name for interrupt-controller@c000000 -> interrupt-controller
[ 0.000000] fixed up name for rom@10000 -> rom
[ 0.000000] fixed up name for serial@64000000 -> serial
[ 0.000000] fixed up name for spi@64001000 -> spi
[ 0.000000] fixed up name for mmc@0 -> mmc
[ 0.000000] fixed up name for tlclk -> tlclk
[ 0.000000] <- unflatten_device_tree()
[ 0.000000] software IO TLB: mapped [mem 0xbb1fc000-0xbf1fc000] (64MB)
[ 0.000000] 0 ffffffe03effcab0 [attach() failed for %s with error %d
[ 0.000000] ] | [cpu]
[ 0.000000] 0 ffffffe03eff0020 [(null)] | [cpu]QEMUga chiqish
SIFIVE, INC.
5555555555555555555555555
5555 5555
5555 5555
5555 5555
5555 5555555555555555555555
5555 555555555555555555555555
5555 5555
5555 5555
5555 5555
5555555555555555555555555555 55555
55555 555555555 55555
55555 55555 55555
55555 5 55555
55555 55555
55555 55555
55555 55555
55555 55555
55555 55555
555555555
55555
5
SiFive RISC-V Core IP
{
#address-cells = <0x00000002>;
#size-cells = <0x00000002>;
compatible = "riscv-virtio";
model = "riscv-virtio,qemu";
chosen {
linux,initrd-start = <0x00000000 0x88000000>;
linux,initrd-end = <0x00000000 0x88442b86>;
riscv,kernel-start = <0x00000000 0x80200000>;
riscv,kernel-end = <0x00000000 0x80c482ac>;
bootargs = "";
stdout-path = <0x2f756172 0x74403130 0x30303030>;
}
uart@10000000 {
interrupts = <0x0000000a>;
interrupt-parent = <0x00000002>;
clock-frequency = <0x00384000>;
reg = <0x00000000 0x10000000 0x00000000 0x00000100>;
compatible = "ns16550a";
}
test@100000 {
reg = <0x00000000 0x00100000 0x00000000 0x00001000>;
compatible = "sifive,test0";
}
virtio_mmio@10008000 {
interrupts = <0x00000008>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10008000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10007000 {
interrupts = <0x00000007>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10007000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10006000 {
interrupts = <0x00000006>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10006000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10005000 {
interrupts = <0x00000005>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10005000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10004000 {
interrupts = <0x00000004>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10004000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10003000 {
interrupts = <0x00000003>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10003000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10002000 {
interrupts = <0x00000002>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10002000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
virtio_mmio@10001000 {
interrupts = <0x00000001>;
interrupt-parent = <0x00000002>;
reg = <0x00000000 0x10001000 0x00000000 0x00001000>;
compatible = "virtio,mmio";
}
cpus {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
timebase-frequency = <0x00989680>;
cpu@0 {
device_type = "cpu";
reg = <0x00000000>;
status = "okay";
compatible = "riscv";
riscv,isa = "rv64imafdcsu";
mmu-type = "riscv,sv48";
clock-frequency = <0x3b9aca00>;
interrupt-controller {
#interrupt-cells = <0x00000001>;
interrupt-controller;
compatible = "riscv,cpu-intc";
linux,phandle = <0x00000001>;
phandle = <0x00000001>;
}
}
}
memory@80000000 {
device_type = "memory";
reg = <0x00000000 0x80000000 0x00000000 0x40000000>;
}
soc {
#address-cells = <0x00000002>;
#size-cells = <0x00000002>;
compatible = "simple-bus";
ranges;
pci@30000000 {
interrupt-map-mask = <0x00001800 0x00000000 0x00000000 0x00000007>;
interrupt-map = <0x00000000 0x00000000 0x00000000 0x00000001 0x00000002 0x00000020 0x00000000 0x00000000 0x00000000 0x00000002 0x00000002 0x00000021 0x00000000 0x00000000 0x00000000 0x00000003 0x00000002 0x00000022 0x00000000 0x00000000 0x00000000 0x00000004 0x00000002 0x00000023 0x00000800 0x00000000 0x00000000 0x00000001 0x00000002 0x00000021 0x00000800 0x00000000 0x00000000 0x00000002 0x00000002 0x00000022 0x00000800 0x00000000 0x00000000 0x00000003 0x00000002 0x00000023 0x00000800 0x00000000 0x00000000 0x00000004 0x00000002 0x00000020 0x00001000 0x00000000 0x00000000 0x00000001 0x00000002 0x00000022 0x00001000 0x00000000 0x00000000 0x00000002 0x00000002 0x00000023 0x00001000 0x00000000 0x00000000 0x00000003 0x00000002 0x00000020 0x00001000 0x00000000 0x00000000 0x00000004 0x00000002 0x00000021 0x00001800 0x00000000 0x00000000 0x00000001 0x00000002 0x00000023 0x00001800 0x00000000 0x00000000 0x00000002 0x00000002 0x00000020 0x00001800 0x00000000 0x00000000 0x00000003 0x00000002 0x00000021 0x00001800 0x00000000 0x00000000 0x00000004 0x00000002 0x00000022>;
ranges = <0x01000000 0x00000000 0x00000000 0x00000000 0x03000000 0x00000000 0x00010000 0x02000000 0x00000000 0x40000000 0x00000000 0x40000000 0x00000000 0x40000000>;
reg = <0x00000000 0x30000000 0x00000000 0x10000000>;
dma-coherent;
bus-range = <0x00000000 0x000002ff>;
linux,pci-domain = <0x00000000>;
device_type = "pci";
compatible = "pci-host-ecam-generic";
#size-cells = <0x00000002>;
#interrupt-cells = <0x00000001>;
#address-cells = <0x00000003>;
}
interrupt-controller@c000000 {
linux,phandle = <0x00000002>;
phandle = <0x00000002>;
riscv,ndev = <0x00000035>;
riscv,max-priority = <0x00000007>;
reg-names = "control";
reg = <0x00000000 0x0c000000 0x00000000 0x04000000>;
interrupts-extended = <0x00000001 0x0000000b 0x00000001 0x00000009>;
interrupt-controller;
compatible = "riscv,plic0";
#interrupt-cells = <0x00000001>;
#address-cells = <0x00000000>;
}
clint@2000000 {
interrupts-extended = <0x00000001 0x00000003 0x00000001 0x00000007>;
reg = <0x00000000 0x02000000 0x00000000 0x00010000>;
compatible = "riscv,clint0";
}
}
}
[ 0.000000] HART = 0 DTB = 80e00000
[ 0.000000] search "chosen", depth: 0, uname:
[ 0.000000] search "chosen", depth: 1, uname: chosen
[ 0.000000] Looking for initrd properties...
[ 0.000000] initrd_start=0x88000000 initrd_end=0x88442b86
[ 0.000000] Command line is: earlyprintk
[ 0.000000] dt_root_size_cells = 2
[ 0.000000] dt_root_addr_cells = 2
[ 0.000000] memory scan node memory@80000000, reg size 16,
[ 0.000000] - 80000000 , 40000000
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Linux version 4.19.0-sifive-1+ (trosinenko@trosinenko-pc) (gcc version 8.3.0 (Buildroot 2019.02-07449-g4eddd28f99)) #1 SMP Sat Jul 6 12:14:41 MSK 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] Initial ramdisk at: 0x(____ptrval____) (4467590 bytes)
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Normal [mem 0x00000000c0000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] INITIAL: ffffffe000c00000
[ 0.000000] -> unflatten_device_tree()
[ 0.000000] Unflattening device tree:
[ 0.000000] magic: d00dfeed
[ 0.000000] size: 00000d56
[ 0.000000] version: 00000011
[ 0.000000] size is 14192, allocating...
[ 0.000000] unflattening (____ptrval____)...
[ 0.000000] fixed up name for ->
[ 0.000000] fixed up name for chosen -> chosen
[ 0.000000] fixed up name for uart@10000000 -> uart
[ 0.000000] fixed up name for test@100000 -> test
[ 0.000000] fixed up name for virtio_mmio@10008000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10007000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10006000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10005000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10004000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10003000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10002000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10001000 -> virtio_mmio
[ 0.000000] fixed up name for cpus -> cpus
[ 0.000000] fixed up name for cpu@0 -> cpu
[ 0.000000] fixed up name for interrupt-controller -> interrupt-controller
[ 0.000000] fixed up name for memory@80000000 -> memory
[ 0.000000] fixed up name for soc -> soc
[ 0.000000] fixed up name for pci@30000000 -> pci
[ 0.000000] fixed up name for interrupt-controller@c000000 -> interrupt-controller
[ 0.000000] fixed up name for clint@2000000 -> clint
[ 0.000000] <- unflatten_device_tree()
[ 0.000000] software IO TLB: mapped [mem 0xbb1fc000-0xbf1fc000] (64MB)
[ 0.000000] 0 ffffffe03effc808 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effca78 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effcd98 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd068 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd230 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd4b8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd740 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd9c8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effdc50 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effded8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe160 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe3e8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe670 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe888 [cpu] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03effec00 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03effeee8 [memory] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff0b0 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff320 [pci] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff858 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efffd58 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effc808 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effca78 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effcd98 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd068 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd230 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd4b8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd740 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd9c8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effdc50 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effded8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe160 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe3e8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe670 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe888 [cpu] | [cpu]
[ 0.000000] elf_hwcap is 0x112d
[ 0.000000] percpu: Embedded 17 pages/cpu @(____ptrval____) s29400 r8192 d32040 u69632
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055
[ 0.000000] Kernel command line: earlyprintk
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 949716K/1046528K available (6565K kernel code, 342K rwdata, 2564K rodata, 208K init, 832K bss, 96812K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[ 0.000000] plic: mapped 53 interrupts to 2 (out of 2) handlers.
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x24e6a1710, max_idle_ns: 440795202120 ns
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] bootconsole [early0] disabled
[ 0.000000] HART = 0 DTB = 80e00000
[ 0.000000] search "chosen", depth: 0, uname:
[ 0.000000] search "chosen", depth: 1, uname: chosen
[ 0.000000] Looking for initrd properties...
[ 0.000000] initrd_start=0x88000000 initrd_end=0x88442b86
[ 0.000000] Command line is: earlyprintk
[ 0.000000] dt_root_size_cells = 2
[ 0.000000] dt_root_addr_cells = 2
[ 0.000000] memory scan node memory@80000000, reg size 16,
[ 0.000000] - 80000000 , 40000000
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Linux version 4.19.0-sifive-1+ (trosinenko@trosinenko-pc) (gcc version 8.3.0 (Buildroot 2019.02-07449-g4eddd28f99)) #1 SMP Sat Jul 6 12:14:41 MSK 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] Initial ramdisk at: 0x(____ptrval____) (4467590 bytes)
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Normal [mem 0x00000000c0000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] INITIAL: ffffffe000c00000
[ 0.000000] -> unflatten_device_tree()
[ 0.000000] Unflattening device tree:
[ 0.000000] magic: d00dfeed
[ 0.000000] size: 00000d56
[ 0.000000] version: 00000011
[ 0.000000] size is 14192, allocating...
[ 0.000000] unflattening (____ptrval____)...
[ 0.000000] fixed up name for ->
[ 0.000000] fixed up name for chosen -> chosen
[ 0.000000] fixed up name for uart@10000000 -> uart
[ 0.000000] fixed up name for test@100000 -> test
[ 0.000000] fixed up name for virtio_mmio@10008000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10007000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10006000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10005000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10004000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10003000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10002000 -> virtio_mmio
[ 0.000000] fixed up name for virtio_mmio@10001000 -> virtio_mmio
[ 0.000000] fixed up name for cpus -> cpus
[ 0.000000] fixed up name for cpu@0 -> cpu
[ 0.000000] fixed up name for interrupt-controller -> interrupt-controller
[ 0.000000] fixed up name for memory@80000000 -> memory
[ 0.000000] fixed up name for soc -> soc
[ 0.000000] fixed up name for pci@30000000 -> pci
[ 0.000000] fixed up name for interrupt-controller@c000000 -> interrupt-controller
[ 0.000000] fixed up name for clint@2000000 -> clint
[ 0.000000] <- unflatten_device_tree()
[ 0.000000] software IO TLB: mapped [mem 0xbb1fc000-0xbf1fc000] (64MB)
[ 0.000000] 0 ffffffe03effc808 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effca78 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effcd98 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd068 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd230 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd4b8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd740 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd9c8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effdc50 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effded8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe160 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe3e8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe670 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe888 [cpu] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03effec00 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03effeee8 [memory] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff0b0 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff320 [pci] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efff858 [<NULL>] | [cpu]
[ 0.000000] ffffffe03effe888 ffffffe03efffd58 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effc808 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effca78 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effcd98 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd068 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd230 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd4b8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd740 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effd9c8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effdc50 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effded8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe160 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe3e8 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe670 [<NULL>] | [cpu]
[ 0.000000] 0 ffffffe03effe888 [cpu] | [cpu]
[ 0.000000] elf_hwcap is 0x112d
[ 0.000000] percpu: Embedded 17 pages/cpu @(____ptrval____) s29400 r8192 d32040 u69632
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055
[ 0.000000] Kernel command line: earlyprintk
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 949716K/1046528K available (6565K kernel code, 342K rwdata, 2564K rodata, 208K init, 832K bss, 96812K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[ 0.000000] plic: mapped 53 interrupts to 2 (out of 2) handlers.
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x24e6a1710, max_idle_ns: 440795202120 ns
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] bootconsole [early0] disabled
[ 0.000000] Calibrating delay loop (skipped), value calculated using timer frequency.. 20.00 BogoMIPS (lpj=100000)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.000000] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.020000] rcu: Hierarchical SRCU implementation.
[ 0.020000] smp: Bringing up secondary CPUs ...
[ 0.020000] smp: Brought up 1 node, 1 CPU
[ 0.050000] devtmpfs: initialized
[ 0.050000] 0 ffffffe03effc808 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effca78 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effcd98 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effd068 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effd230 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effd4b8 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effd740 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effd9c8 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effdc50 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effded8 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effe160 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effe3e8 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effe670 [<NULL>] | [cpu]
[ 0.050000] 0 ffffffe03effe888 [cpu] | [cpu]
[ 0.050000] random: get_random_u32 called from bucket_table_alloc+0x76/0x17a with crng_init=0
[ 0.050000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.050000] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.060000] NET: Registered protocol family 16
[ 0.090000] vgaarb: loaded
[ 0.090000] SCSI subsystem initialized
[ 0.090000] usbcore: registered new interface driver usbfs
[ 0.090000] usbcore: registered new interface driver hub
[ 0.090000] usbcore: registered new device driver usb
[ 0.090000] pps_core: LinuxPPS API ver. 1 registered
[ 0.090000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 0.090000] PTP clock support registered
[ 0.100000] Advanced Linux Sound Architecture Driver Initialized.
[ 0.100000] clocksource: Switched to clocksource riscv_clocksource
[ 0.110000] NET: Registered protocol family 2
[ 0.110000] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes)
[ 0.110000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.110000] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 0.110000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.110000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.110000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.110000] NET: Registered protocol family 1
[ 0.120000] Unpacking initramfs...
[ 0.590000] workingset: timestamp_bits=62 max_order=18 bucket_order=0
[ 0.620000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.620000] io scheduler noop registered
[ 0.620000] io scheduler deadline registered
[ 0.620000] io scheduler cfq registered (default)
[ 0.620000] io scheduler mq-deadline registered
[ 0.620000] io scheduler kyber registered
[ 0.620000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 0.690000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.690000] 10000000.uart: ttyS0 at MMIO 0x10000000 (irq = 10, base_baud = 230400) is a 16550A
[ 0.720000] console [ttyS0] enabled
[ 0.720000] [drm] radeon kernel modesetting enabled.
[ 0.720000] [drm] amdgpu kernel modesetting enabled.
[ 0.730000] loop: module loaded
[ 0.730000] libphy: Fixed MDIO Bus: probed
[ 0.740000] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 0.740000] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 0.740000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.740000] ehci-pci: EHCI PCI platform driver
[ 0.740000] ehci-platform: EHCI generic platform driver
[ 0.740000] mousedev: PS/2 mouse device common for all mice
[ 0.740000] usbcore: registered new interface driver usbhid
[ 0.740000] usbhid: USB HID core driver
[ 0.740000] usbcore: registered new interface driver snd-usb-audio
[ 0.740000] NET: Registered protocol family 10
[ 0.750000] Segment Routing with IPv6
[ 0.750000] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 0.750000] NET: Registered protocol family 17
[ 0.750000] Key type dns_resolver registered
[ 0.760000] ALSA device list:
[ 0.760000] No soundcards found.
[ 0.770000] Freeing unused kernel memory: 208K
[ 0.770000] This architecture does not have kernel memory protection.
[ 0.770000] Run /init as init process("Vaqt tamg'asi" chiziqlari yadro tomonidan chiqariladi, ularning oldida daraxt BBL tomonidan chiqariladi) Bir tomondan, FDT muvaffaqiyatli o'qiladi, boshqa tomondan, tahlil qilishda qandaydir bema'nilik olinadi " ob'ekt" daraxti.
Nosozliklarni tuzatish jarayonida men BBL konfiguratsiyada xatolik borligi uchun emas, balki ildiz tugunida "ikkilamchi" manzilni o'qiy olmasligini tushundim. #address-cells = <1>; #size-cells = <1>;.
Nosozliklarni tuzatish chiqishini kengaytirib, men bu ko'rsatkichlarni ko'rdim type ΠΈ name "kaltaklangan" va juda g'alati tarzda: ularning birinchi bayti (noldan boshlab) nolga qaytarildi, shunga o'xshash narsa 0xabcdef -> 0xab00ef. Men tanish taktikani qo'llashim kerak edi: shikastlangan xotira joylashgan manzillarni bilib, uni funktsiyaga qo'shing. printk ushbu ma'lumotlarni chop eting. Xo'sh, qiyinchiliklarning o'zi printk ularni kam bo'lgan joyga tarqating. Afsuski, bu unchalik aniq bo'lmadi. Keyin men demontaj qilinganlar bilan maslahatlashishni boshladim objdump versiyada to'xtash nuqtalarini qo'lda o'rnating va kodning muammoli qismini bosqichma-bosqich o'ting. Va keyin sirli va yoqimsiz narsa aniqlandi: agar men darhol ma'lum bo'lgan yaxshi holatdan nisbatan uzoqroq joyda to'xtash nuqtasini qo'ysam, unda to'xtab, allaqachon buzilgan xotirani ko'raman. Ammo agar siz asta-sekin unga yashirincha kirishga harakat qilsangiz, xato yashirinishga muvaffaq bo'ladi! Agar siz doimiy ravishda kerakli qiymatni so'rasangiz, xatoni yashiradigan buzilgan xotira tekshiruvi va kesh kabi hidlanadi. Agar .. bo'lsa nima bo'ladiβ¦
Xotirani almashtirish
Men tomonda bo'lmagan muammoni hal qilish imkoniyatiga yopishib oldim, ehtimol men singan xotira kartasini olganman deb o'yladim. Keyin o'n yillik netbuk nafaqat portativ kompyuter, balki DDR2 SO-DIMM ning qimmatli manbai ekanligini esladim. Bonus sifatida siz platadan olib tashlangan xotirani unga qo'yishingiz va Memtest-ni deyarli bir zumda osib qo'yishingiz mumkin (Aytgancha, Linux deyarli grafik qobiqqa yuklangan). Ammo agar siz o'rnatilgan disklardagi ma'lumotlarni qadrlasangiz, bu tajribani takrorlamaslik yaxshiroqdir ...). Bir tomondan, xotira ushbu aniq netbukka mos kelmadi deb taxmin qilishimiz mumkin. Boshqa tomondan, u yuklashga muvaffaq bo'ldi! Xotira shunchaki "buzilgan" degan umid bor edi va muammo mening o'ramimda emas edi.
Bu shuni anglatadiki, siz netbuk xotirasi bilan vaqtincha ishga tushirishga harakat qilishingiz kerak. Afsuski, Quartus 18 ushbu IP yadrosini tahrirlash uchun qanday yangilashni bilmaydi. Bu, nihoyat, yangi misollarni qanday yaratishni o'rganish vaqti kelganligini anglatadi. Hammasi juda oddiy bo'lib chiqdi: biz IP-katalogida ALTMEMPHY Intel FPGA IP-ga ega DDR2 SDRAM Controller elementini qidiramiz va biz avvalgidek interfeysga ega blokni olamiz. Bitta muammo to'g'ri xotira sozlamalarini o'rnatishdir.
Xotira modulining parametrlarini olish
Modulni sozlashning nisbatan aniq usuli bor: SPD parametrlarini o'qing. Haqiqatan ham, agar oddiy kompyuter SPD ma'lumotlarini o'qisa va unga asoslangan boshqaruvchini sozlasa, keling, mavjud netbukda ushbu ma'lumotlarni ayirib, jadvalga kiritamiz.
Bu Ubuntu-da amalga oshiriladi : paketni o'rnatishingiz kerak i2c-tools, modullarni yuklash eeprom ΠΈ i2c-i801 (Biroq, ikkinchi haydovchi hamma joyda ishlashiga ishonchim komil emas), keyin ishga tushiring decode-dimms:
decode-dimms chiqishi
# decode-dimms version 6231 (2014-02-20 10:54:34 +0100)
Memory Serial Presence Detect Decoder
By Philip Edelbrock, Christian Zuckschwerdt, Burkart Lingner,
Jean Delvare, Trent Piepho and others
Decoding EEPROM: /sys/bus/i2c/drivers/eeprom/0-0050
Guessing DIMM is in bank 1
---=== SPD EEPROM Information ===---
EEPROM Checksum of bytes 0-62 OK (0x00)
SPD Revision Invalid
Fundamental Memory type Unknown (0x00)
---=== Manufacturing Information ===---
Manufacturer Undefined
Part Number Undefined
Decoding EEPROM: /sys/bus/i2c/drivers/eeprom/4-0050
Guessing DIMM is in bank 1
---=== SPD EEPROM Information ===---
EEPROM Checksum of bytes 0-62 OK (0x00)
SPD Revision Invalid
Fundamental Memory type Unknown (0x00)
---=== Manufacturing Information ===---
Manufacturer Undefined
Part Number Undefined
Decoding EEPROM: /sys/bus/i2c/drivers/eeprom/6-0050
Guessing DIMM is in bank 1
---=== SPD EEPROM Information ===---
EEPROM Checksum of bytes 0-62 OK (0x76)
# of bytes written to SDRAM EEPROM 128
Total number of bytes in EEPROM 256
Fundamental Memory type DDR2 SDRAM
SPD Revision 1.2
---=== Memory Characteristics ===---
Maximum module speed 800 MHz (PC2-6400)
Size 1024 MB
Banks x Rows x Columns x Bits 8 x 13 x 10 x 64
Ranks 2
SDRAM Device Width 16 bits
Module Height 30.0 mm
Module Type SO-DIMM (67.6 mm)
DRAM Package Planar
Voltage Interface Level SSTL 1.8V
Module Configuration Type No Parity
Refresh Rate Reduced (7.8 us) - Self Refresh
Supported Burst Lengths 4, 8
tCL-tRCD-tRP-tRAS 6-6-6-18
Supported CAS Latencies (tCL) 6T, 5T, 4T
Minimum Cycle Time 2.50 ns at CAS 6 (tCK min)
3.00 ns at CAS 5
3.75 ns at CAS 4
Maximum Access Time 0.40 ns at CAS 6 (tAC)
0.45 ns at CAS 5
0.50 ns at CAS 4
Maximum Cycle Time (tCK max) 8.00 ns
---=== Timing Parameters ===---
Address/Command Setup Time Before Clock (tIS) 0.17 ns
Address/Command Hold Time After Clock (tIH) 0.25 ns
Data Input Setup Time Before Strobe (tDS) 0.05 ns
Data Input Hold Time After Strobe (tDH) 0.12 ns
Minimum Row Precharge Delay (tRP) 15.00 ns
Minimum Row Active to Row Active Delay (tRRD) 10.00 ns
Minimum RAS# to CAS# Delay (tRCD) 15.00 ns
Minimum RAS# Pulse Width (tRAS) 45.00 ns
Write Recovery Time (tWR) 15.00 ns
Minimum Write to Read CMD Delay (tWTR) 7.50 ns
Minimum Read to Pre-charge CMD Delay (tRTP) 7.50 ns
Minimum Active to Auto-refresh Delay (tRC) 60.00 ns
Minimum Recovery Delay (tRFC) 127.50 ns
Maximum DQS to DQ Skew (tDQSQ) 0.20 ns
Maximum Read Data Hold Skew (tQHS) 0.30 ns
---=== Manufacturing Information ===---
Manufacturer Samsung
Manufacturing Location Code 0x02
Part Number M4 70T2864QZ3-CF7
Revision Code 0x3351
Manufacturing Date 2009-W34
Assembly Serial Number 0x79C64E9A
Number of SDRAM DIMMs detected and decoded: 3Muammo shundaki, bu erda ba'zi vaqtlar ko'rsatilmagan, shuning uchun ikkinchi yo'lni olaylik.
Modullarimizda nima yozilgan:
Bunday holda, xotira chiplaridagi yozuv yanada qiziqroq: K4T1G164QQ-HCF7. Ushbu qatorni Google-ga kiritish orqali biz barcha kerakli parametrlarga ega bo'lgan bir necha o'nlab sahifalardan iborat ma'lumotlar jadvalini olamiz, ular IP Core xususiyatlariga aniq kiritilishi mumkin. Faqat o'lchov birliklariga e'tibor bering: bir joyda ns, bir joyda - ps, va ba'zan hatto baham ko'radi tCK. Men sizga nimaga e'tibor berishni o'rgatmayman - men o'zim tasodifan juda ko'p narsalarni sozladim (xotira yoki FPGAni shu tarzda "yoqib yubora olmaysiz" deb kafolat berolmayman). Men sizning e'tiboringizni bunga qaratmoqchiman: men kontrollerni juda uzoq vaqt ishlay olmadim va oxirgi qadam barcha xotira interfeyslarining kengligini yaratilgan Verilog kodiga muvofiqligini tekshirishim kerakligini angladim. : axir, kirganda MemIfBundle ko'rsatilgan val mem_ba = IO(Output(UInt(2.W))), va 8 ta bank (ya'ni, 3 bit kenglikdagi manzil) mavjud, keyin bizda havoda osilgan xotira tekshirgichining chiqishi - muammo, lekin muhim emas, shuning uchun hamma narsa sintezlanadi, lekin ishlamaydi.
Ehtimol, agar boshqaruvchi yangilangan bo'lsa, hamma narsa eski modul bilan ishlaydi, ammo hozircha men potentsial suzuvchi xatolar bilan shug'ullanish uchun juda dangasaman: menda o'zim etarli.
Shunday qilib, ko'chib o'tgandan keyin timebase-frequency DTS da ma'lum CPU darajasidan tugun darajasiga qadar cpus (yadroning tushunarli so'roviga ko'ra) biz quyidagilarni olamiz:
Yashirin matn
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Linux version 4.19.0-sifive-1+ (trosinenko@trosinenko-pc) (gcc version 8.3.0 (Buildroot 2019.02-07449-g4eddd28f99)) #1 SMP Tue Jul 9 22:42:36 MSK 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] Initial ramdisk at: 0x(____ptrval____) (16777216 bytes)
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Normal [mem 0x00000000c0000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
[ 0.000000] software IO TLB: mapped [mem 0xbb1fc000-0xbf1fc000] (64MB)
[ 0.000000] elf_hwcap is 0x112d
[ 0.000000] percpu: Embedded 17 pages/cpu @(____ptrval____) s29400 r8192 d32040 u69632
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055
[ 0.000000] Kernel command line: debug console=ttySIF0,125200 root=/dev/mmcblk0p2 loglevel=7 rootwait
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 937696K/1046528K available (6565K kernel code, 343K rwdata, 2564K rodata, 208K init, 832K bss, 108832K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[ 0.000000] plic: mapped 8 interrupts to 1 (out of 2) handlers.
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
[ 0.020000] pid_max: default: 32768 minimum: 301
[ 0.030000] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.040000] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.140000] rcu: Hierarchical SRCU implementation.
[ 0.190000] smp: Bringing up secondary CPUs ...
[ 0.190000] smp: Brought up 1 node, 1 CPU
[ 0.220000] devtmpfs: initialized
[ 0.300000] random: get_random_u32 called from bucket_table_alloc+0x76/0x17a with crng_init=0
[ 0.330000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.340000] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.380000] NET: Registered protocol family 16
[ 1.850000] vgaarb: loaded
[ 1.870000] SCSI subsystem initialized
[ 1.900000] usbcore: registered new interface driver usbfs
[ 1.910000] usbcore: registered new interface driver hub
[ 1.920000] usbcore: registered new device driver usb
[ 1.930000] pps_core: LinuxPPS API ver. 1 registered
[ 1.940000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 1.950000] PTP clock support registered
[ 1.970000] Advanced Linux Sound Architecture Driver Initialized.
[ 2.010000] clocksource: Switched to clocksource riscv_clocksource
[ 2.600000] NET: Registered protocol family 2
[ 2.640000] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes)
[ 2.650000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 2.670000] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 2.700000] TCP: Hash tables configured (established 8192 bind 8192)
[ 2.720000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 2.730000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 2.750000] NET: Registered protocol family 1
[ 2.770000] Unpacking initramfs...
[ 23.980000] Initramfs unpacking failed: junk in compressed archive
[ 24.030000] workingset: timestamp_bits=62 max_order=18 bucket_order=0
[ 25.020000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 25.030000] io scheduler noop registered
[ 25.040000] io scheduler deadline registered
[ 25.050000] io scheduler cfq registered (default)
[ 25.060000] io scheduler mq-deadline registered
[ 25.060000] io scheduler kyber registered
[ 25.120000] sifive_gpio 64002000.gpio: SiFive GPIO chip registered 6 GPIOs
[ 25.150000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 28.870000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 28.940000] sifive-serial 64000000.serial: unable to find controller clock
[ 28.950000] sifive-serial: probe of 64000000.serial failed with error -2
[ 28.980000] [drm] radeon kernel modesetting enabled.
[ 28.990000] [drm] amdgpu kernel modesetting enabled.
[ 29.500000] loop: module loaded
[ 29.610000] sifive_spi 64001000.spi: Unable to find bus clock
[ 29.620000] sifive_spi: probe of 64001000.spi failed with error -2
[ 29.640000] libphy: Fixed MDIO Bus: probed
[ 29.680000] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 29.690000] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 29.700000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 29.710000] ehci-pci: EHCI PCI platform driver
[ 29.720000] ehci-platform: EHCI generic platform driver
[ 29.750000] mousedev: PS/2 mouse device common for all mice
[ 29.790000] usbcore: registered new interface driver usbhid
[ 29.800000] usbhid: USB HID core driver
[ 29.820000] usbcore: registered new interface driver snd-usb-audio
[ 29.900000] NET: Registered protocol family 10
[ 29.960000] Segment Routing with IPv6
[ 29.960000] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 30.020000] NET: Registered protocol family 17
[ 30.020000] Key type dns_resolver registered
[ 30.070000] bootconsole [early0] uses init memory and must be disabled even before the real one is ready
[ 30.080000] bootconsole [early0] disabledShundan keyin ko'rinadigan hech narsa bo'lmaydi.
Endi siz uchta muammoni hal qilishga harakat qilishingiz mumkin:
[ 23.980000] Initramfs unpacking failed: junk in compressed archive
...
[ 28.940000] sifive-serial 64000000.serial: unable to find controller clock
...
[ 29.610000] sifive_spi 64001000.spi: Unable to find bus clock... va shuningdek, konsolga chiqishni to'xtatadi.
Chastotalar bilan bog'liq ikkita muammoni yengish unchalik qiyin emas: siz ball qo'shishingiz kerak clocks Qulaylik uchun tugun uchun aniq yorliq nomini berish uchun kerakli qurilmalarning pastki daraxtlariga kiriting tlclk:
diff --git a/arch/riscv/dts/zeowaa-1gb.dts b/arch/riscv/dts/zeowaa-1gb.dts
index 4b2cebc..1347e76 100644
--- a/arch/riscv/dts/zeowaa-1gb.dts
+++ b/arch/riscv/dts/zeowaa-1gb.dts
@@ -96,6 +97,7 @@
L8: serial@64000000 {
compatible = "sifive,uart0";
interrupt-parent = <&L0>;
+ clocks = <&tlclk>;
interrupts = <2>;
reg = <0x64000000 0x1000>;
reg-names = "control";
@@ -107,6 +109,7 @@
interrupt-parent = <&L0>;
interrupts = <1>;
reg = <0x64001000 0x1000>;
+ clocks = <&tlclk>;
reg-names = "control";
L12: mmc@0 {
compatible = "mmc-spi-slot";
@@ -116,7 +119,7 @@
voltage-ranges = <3300 3300>;
};
};
- L11: tlclk {
+ tlclk: tlclk {
#clock-cells = <0>;
clock-frequency = <25000000>;
clock-output-names = "tlclk";Chiziqni qo'shish orqali #define pr_debug printk faylning boshiga init/initramfs.cinitramfs o'rniga axlat haqida xabarni ko'rsatadigan , biz biroz batafsilroq xabarni olamiz:
[ 2.760000] Unpacking initramfs...
[ 2.770000] Detected gzip compressed data
[ 23.940000] Detected (null) compressed data
[ 23.970000] Initramfs unpacking failed: junk in compressed archiveYa'ni, ehtimol, axlat emas o'rniga initramfs va Π²ΠΌΠ΅ΡΡΠ΅.
Mayli, u nimadir topdi, ehtimol bu yetarli. Konsol qayerga ketdi? Qidiruv Github-dagi muammoga havola beradi: β maβlum boβlishicha, birgina UART, haydovchining soβzlariga koβra, bu haqda gapirishga ham arzimaydi. Lekin 11 yil 2018 iyul - bir yil oldin. Ma'lum bo'lishicha, bu majburiyat hech qachon men yadro qurayotgan daraxtga kirmagan. Ushbu yamoqni qo'lda qo'llash orqali men ishlaydigan Linuxga ega bo'ldim! Ma'lum bo'lishicha, initramfs bilan bog'liq muammo haqiqatan ham muhim emas edi.
User=root, password=sifive sifatida tizimga kirganimda, men hech qanday muammosiz kirishga muvaffaq bo'ldim (GPIO raqamida hamma narsa hisoblab chiqiladigan va faqat tegishli psevdo-fayldan o'qilishi kerak bo'lgan asos borligini tushunishdan tashqari) orqali sysfs doskadagi LEDni yoqing.
O'tgan safargidek, men Linux ishga tushirilganligi haqidagi matnli videoni ilova qilyapman. Konsol erta chop etishdan standartga o'tganda, UART tezligi noto'g'ri o'rnatilgandagi chiqishga o'xshash qandaydir axlat paydo bo'ladi. Qizig'i, futbolchi bu "tartibsizlik" orqali muvaffaqiyatli ishladi.
Manba: www.habr.com